Abstract:The abundance of low-temperature waste heat produced by industry and automobile exhaust necessitates the development of power generation with thermoelectric (TE) materials. Commercially available bismuth telluride-based alloys are generally used near room temperature. Materials that are composed of p-type bismuth telluride, which are suitable for low-temperature power generation (near 380 K), were successfully obtained through Sb-alloying, which suppresses detrimental intrinsic conduction at elevated temperatures by increasing hole concentrations and material band gaps. Furthermore, hot deformation (HD)-induced multi-scale microstructures were successfully realized in the high-performance p-type TE materials. Enhanced textures and donor-like effects all contributed to improved electrical transport properties. Multiple phonon scattering centers, including local nanostructures induced by dynamic recrystallization and high-density lattice defects, significantly reduced the lattice thermal conductivity. These combined effects resulted in observable improvement of ZT over the entire temperature range, with all TE parameters measured along the in-plane direction. The maximum ZT of 1.3 for the hot-deformed Bi0.3Sb1.7Te3 alloy was reached at 380 K, whereas the average ZTav of 1.18 was found in the range of 300–480 K, indicating potential for application in low-temperature TE power generation. Thermoelectric materials, which convert temperature differences and electric voltage into each other, serve in refrigeration or power generation applications. Currently, bismuth telluride (Bi2Te3) and its alloys are the most widely used thermoelectric materials. Tie-Jun Zhu, Xin-Bing Zhao and co-workers from Zhejiang University, China, have now investigated the effect of antimony (Sb) alloying on bismuth tellurides through a series of polycrystalline solid solutions of Bi2-xSbxTe3—where x varies between 1.4 and 1.8—prepared by hot deformation. Systematic tuning of the alloy composition showed that higher antimony content raised the material's optimal conversion temperature by repressing undesirable conduction. This effect arises from an increase in both the hole concentration and the band gap in the material. For a composition where x is 1.7, the alloy showed optimal performances at 380 kelvin—a suitable temperature for low-temperature power generation from the waste heat generated by industry or vehicles. The p-type bismuth telluride-based polycrystalline materials suiting for low-temperature power generations (near 380 K) have been obtained through Sb-alloying and HD, which suppresses the detrimental effect of intrinsic conduction at elevated temperature via increasing the hole concentration and band gap. The hot-deformed Bi0.3Sb1.7Te3 alloy, not usual composition Bi0.5Sb1.5Te3, shows a maximum ZT of 1.3 at 380 K, indicating a bright application potential in low-temperature power generations.

Low Thermal Conductivity and High Figure of Merit for Rapidly Synthesized N-Type Pb1-xBixTe Alloys

Trace bismuth and iodine co-doping enhanced thermoelectric performance of PbTe alloys

The High Thermoelectric Performance of Slightly Sb Doped PbTe Alloys

Thermoelectric properties and thermal stability of Bi-doped PbTe single crystal

Enhanced Thermoelectric Properties Obtained by Compositional Optimization in P -Type Bi X Sb 2− X Te 3 Fabricated by Mechanical Alloying and Spark Plasma Sintering

N-Type Bi-doped PbTe Nanocubes with Enhanced Thermoelectric Performance

Synthesis and thermoelectric properties of nanostructured bismuth telluride alloys

Fast Preparation and High Thermoelectric Performance of the Stable Bi 0.5 Sb 1.5 Te 3 Bulk Materials for Different Synthesis Pressures

High-Performance P-Type Bi2Te3-Based Thermoelectric Materials Enabled Via Regulating Bi-Te Ratio

High Thermoelectric Performance in Supersaturated Solid Solutions and Nanostructured N‐type PbTe–GeTe

Shifting Up the Optimum Figure of Merit of P-Type Bismuth Telluride-Based Thermoelectric Materials for Power Generation by Suppressing Intrinsic Conduction

High Thermoelectric Performance of BixSb2−xTe3 Alloy Achieved Via Structural Manipulation under Optimized Heat Treatment

Enhanced Thermoelectric Performance in N-Type Bi2Te3-Based Alloys Via Suppressing Intrinsic Excitation.

Regulation of exciton for high thermoelectric performance in (Bi, Sb)2Te3 alloys via doping with Pb and multi-scale microstructure

Synergistic Suppression of Bipolar Effect and Lattice Thermal Conductivity Leading to High Average Figure of Merit in Bi0.4Sb1.6Te3 Materials Through Alloying with AgSbTe2

Enhanced thermoelectric properties of Pb1-xBixS prepared with hydrothermal synthesis and microwave sintering

Tunable Electrical Conductivity and Simultaneously Enhanced Thermoelectric and Mechanical Properties in n-type Bi<sub>2</sub>Te<sub>3</sub>

Enhanced Thermoelectric Properties of Bismuth and Zinc Co-Doped SnTe by Band Engineering and All-Scale Structure Defects

Tunable Electrical Conductivity and Simultaneously Enhanced Thermoelectric and Mechanical Properties in n‐type Bi2Te3

Low Thermal Conductivity and Improved Figure of Merit in Fine-Grained Binary PbTe Thermoelectric Alloys

High thermoelectric performance in Bi0.46Sb1.54Te3 nanostructured with ZnTe