Abstract:An effective additive engineering strategy is reported where N‐succinimidyl 6‐maleimidohexanoate (NSMH) with bidirectional active site and hydrophobic alkyl chains are introduced into perovskite precursor to eliminate undercoordinated Pb2+ traps in perovskite films. The efficiency improves from 20.67% to 22.40% after NSMH modification along with improved stability. The nonradiative recombination induced by trap states at the surface and grain boundaries impedes the further increase of power conversion efficiency (PCE) and stability of perovskite solar cells (PSCs). Consequently, it is highly desirable to minimize the trap‐assisted nonradiative recombination in perovskite films. Here, an effective additive engineering strategy is reported where N‐succinimidyl 6‐maleimidohexanoate (denoted as NSMH) with multiple active sites and hydrophobic alkyl chains were incorporated for fully eliminating undercoordinated Pb2+ traps in perovskite films. It is revealed that improved crystallinity and reduced defect density are achieved, which is ascribed to the strong coordination interaction between the carbonyl groups at both sides of NSMH molecules and Pb2+. As a result, the NSMH‐modified device exhibits a champion PCE of 22.40% with negligible hysteresis, which is significantly higher than 20.67% of the control device. The unencapsulated modified device exhibits no degradation while the control device degrades to 82% of its initial PCE after storing for 1536 h in a relative humidity of 10–20% at room temperature in the dark.

Efficient Grain Boundary Suture by Low-Cost Tetra-ammonium Zinc Phthalocyanine for Stable Perovskite Solar Cells with Expanded Photoresponse

Stable and environmentally friendly perovskite solar cells induced by grain boundary engineering with self-assembled hydrogen-bonded porous frameworks

Enhancing perovskite solar cells performance via sewing up the grain boundary

Tri‐Brominated Perovskite Film Management and Multiple‐Ionic Defect Passivation for Highly Efficient and Stable Solar Cells

Grain Boundary Engineering with Self-Assembled Porphyrin Supramolecules for Highly Efficient Large-Area Perovskite Photovoltaics

Zn‐Porphyrin Antisolvent Engineering Enhanced Grain Boundary Passivation for High‐Performance Perovskite Solar Cell

Interface and Grain Boundary Passivation by PEA-SCN Double Ions via One-Step Crystal Engineering for All Air-Processed, Stable Perovskite Solar Cells

Synchronous surface reconstruction and grain boundary healing toward efficient and stable inverted CsPbI3 perovskite solar cells

Spatially selective defect management of CsPbI3 films for high-performance carbon-based inorganic perovskite solar cells

Tungstate-mediated In-situ Passivation of Grain Boundary Grooves in Perovskite Solar Cells.

Grain Boundary Passivation with Dion–Jacobson Phase Perovskites for High‐Performance Pb–Sn Mixed Narrow‐Bandgap Perovskite Solar Cells

Highly Stable Perovskite Solar Cells with Protective Layers Obtained via Interfacial Modification

Modifying Surface Termination of CsPbI 3 Grain Boundaries by 2D Perovskite Layer for Efficient and Stable Photovoltaics

Covalently Connecting Crystal Grains with Polyvinylammonium Carbochain Backbone To Suppress Grain Boundaries for Long-Term Stable Perovskite Solar Cells

Stable High‐Performance Perovskite Solar Cells via Grain Boundary Passivation

Conjugated Polymer–Assisted Grain Boundary Passivation for Efficient Inverted Planar Perovskite Solar Cells

Grain Boundary Chemical Anchoring via Bidirectional Active Site Additive Enables Efficient and Stable Perovskite Solar Cells

Synchronous Surface Reconstruction and Defect Passivation for High-Performance Inorganic Perovskite Solar Cells.

Interfacial modification engineering for efficient and stable MA-free wide-bandgap perovskite solar cells by grain regrowth

Deactivating grain boundary defect by bifunctional polymer additive for humid air-synthesized stable halide perovskite solar cells

Cementitious grain-boundary passivation for flexible perovskite solar cells with superior environmental stability and mechanical robustness