Abstract:Total knee arthroplasty (TKA) is a cornerstone in addressing knee joint disorders, significantly enhancing patients' quality of life. However, despite technological advancements, a comprehensive understanding of the dynamic stresses experienced by knee prostheses during daily activities, particularly under rehabilitation interventions, remains elusive. This study aims to bridge this gap by employing numerical simulations and finite element analysis to elucidate these dynamic stresses and their interaction with rehabilitation protocols. A real-life knee replacement prosthesis model was meticulously constructed through coordinate measuring and 3D scanning, facilitating detailed finite element analysis in ANSYS Workbench version 17.1. Two distinct boundary conditions and loading scenarios were applied, with comparisons made between linear and nonlinear material assumptions. The simulation results using these different boundary condition methods revealed minimal differences. Specifically, at a knee angle of 0°, the relative stress error rate between the two boundary condition types was approximately 1 % (1.11 MPa and 1.099 MPa, respectively). At 15° and 90°, the error rates were 1.9 % and 0.56 %, respectively (10.275 MPa and 10.078 MPa at 15°; 10.275 MPa and 10.078 MPa at 90°). Given these minimal differences, the first type of boundary condition was adopted for the subsequent scenarios to enhance convergence efficiency in the analysis. Moreover, comparative analyses between linear and nonlinear material behaviors demonstrated acceptable agreement, offering insights into potential efficiency gains in simulation methodologies. Building on this foundation, an optimized tibial model was proposed, incorporating geometric alterations to the tray. Quantitative assessments revealed significant reductions, with von Mises stress decreasing by 23.35 % and equivalent strain by 17 % at a knee angle of 140°. Further evaluations at varying angles, including 60°, consistently showed positive influences on stress and strain. These quantitative findings not only contribute valuable insights into the mechanical behavior of knee prostheses but also provide tangible evidence for the efficacy of linear material behavior assumptions. The proposed optimized model exhibits promising potential for enhancing the design and performance of knee prostheses, particularly under critical loading conditions. In conclusion, these results underscore the importance of a nuanced understanding of knee prosthesis behavior during rehabilitation, offering a quantitative foundation for refining existing designs and informing the development of next-generation prostheses.

Optimization of Parameters for Femoral Component Implantation During TKA Using Finite Element Analysis and Orthogonal Array Testing

An Optimization Method for Implantation Parameters of Individualized TKA Tibial Prosthesis Based on Finite Element Analysis and Orthogonal Experimental Design.

Positioning Optimization of the Femoral Component in Total Knee Arthroplasty by Using Finite Element Analysis and Orthogonal Experiment

Finite element analysis in the optimization of posterior-stabilized total knee arthroplasty

Application strategy of finite element analysis in artificial knee arthroplasty

The construction of three-dimensional finite element model of TKA knee

Finite Element Analysis of Total Knee Replacement with Various Misalignment Angles in the Sagittal Plane

Biomechanical Assessment of a Patient-Specific Knee Implant Design Using Finite Element Method

Optimizing functionally graded tibial components for total knee replacements: a finite element analysis and multi-objective optimization study

Effect of Femoral Component Flexion Implantation on the Mediolateral Bone-Prosthetic Fit in Total Knee Arthroplasty

Finite element study of stress distribution in medial UKA under varied lower limb alignment

Finite-element analysis of the influence of tibial implant fixation design of total ankle replacement on bone-implant interfacial biomechanical performance

Morphological Evaluation of the Sagittal Plane Femoral Load-Bearing Surface in Computer-Simulated Virtual Total Knee Arthroplasty Implantation at Different Flexion Angles.

Computational Lower Limb Simulator Boundary Conditions to Reproduce Measured TKA Loading in a Cohort of Telemetric Implant Patients

Finite Element Analysis of Fixed-Bearing Knee Prosthesis with Different Size of Femur and Tibia Parts

Variation of Femoral Component Size by Reference Points and Target Alignments in Total Knee Arthroplasty

Optimal Flexion for the Femoral Component in TKR: A Study of Angle Between Mechanical Axis and Distal Anatomic Intramedullary Axis Using 3D Reconstructed CT Scans in 407 Osteoarthritic Knees Studied in India

Finite Element Analysis of A Retrieved Custom-Made Knee Prosthesis

The accuracy of bony resection and component size planning of total knee arthroplasty assisted with a novel designed patient-specific instrumentation

Numerical investigation of knee prosthesis stresses in daily activities: Insight into knee rehabilitation and Creation of a new optimal model

Finite element stress analysis of the bearing component and bone resected surfaces for total ankle replacement with different implant material combinations