Abstract:Sulfur is a promising active material for the lithium rechargeable batteries because of its high theoretical capacity, a relatively low cost, and an environmentally friendly nature. Lithium–sulfur battery with a high-energy-density is regarded as a third-generation rechargeable battery with high potential for commercialization. The well charged and discharged lithium–sulfur battery can generate specific energy density of up to 600 W∙h kg −1 . However, the charging product, sulfur, and the discharging product, lithium sulfide, both have low conductivity, which lead to low active material utilization and excessive addition of conductive materials, lowering the active material content and performance in the cathode region. The liquid active material, polysulfides, formed in the middle of the cycling reaction will dissolve in the electrolyte, causing leakage to the lithium anode to form a non-reactive lithium sulfide layer, causing severe capacity fading. Furthermore, the repeated transformation of sulfur (solid-state), polysulfides (liquid-state), and lithium sulfur (solid-state) active materials led to the sluggish battery reaction and irreversible electrolyte consumption. All and all, the chemical and physical properties of the sulfur and the combination with lithium resulted in low active material utilization, low cycling ability, low capacity-retention rate, and shortened cycle life. To fully realize the potential of the high-energy-density lithium–sulfur battery, the cathode material, configuration, and fabrication must be carefully considered. Herein, a sulfur cathode fabricated by a hot-pressing method and the evaluation of different porous substrate was also conducted. Porous conductive network is a common cathode material, which provides a large surface area and great polysulfides absorbability. However, as a result of high-sulfur-loading and lean-electrolyte cathode batteries, a low specific capacity and short cycle life are discovered, which is affected by the high electrolyte consumption. Accordingly, a carbon electrospun substrate with a non-nanoporous structure was introduced as the conductive network to achieve the high-energy-density battery design. To fabricate the free-standing sulfur cathode, sulfur powder was loaded between two porous carbon electrospun substrate by a hot-pressing technique. The cathode consists of three layers: carbon current collector, melt-in sulfur layer, and carbon interlayer, forming a sandwich-like cathode. With this design, we can accommodate high areal loading of sulfur (8 mg cm −2 ) in the cathode area while lessening the conductive additive (sulfur content of 73 wt%). The hot-pressed electrospun cathode, conducted under low electrolyte usage (i.e., the low electrolyte-to-sulfur ratio of 7 μL mg −1 ) can achieve excellent energy density (11.8 mW∙h cm −2 ) with a stable areal capacity up to 5.9 mA∙h cm − 2 let alone with an extended cycle life over 200 cycles. Furthermore, this devised cathode can also retain excellent cycling ability with lower ratios of electrolyte to sulfur (6–4 μL mg −1 ) and great rate dependent performance up to C/2 cycling rate. Figure 1

Enabling High Energy Density Cathode for Lithium-Sulfur Batteries.

High Sulfur Loading of Cathodes for Li-S Batteries

Towards Full Demonstration of High Areal Loading Sulfur Cathode in Lithium–sulfur Batteries

Understanding of Low‐Porosity Sulfur Electrode for High‐Energy Lithium–Sulfur Batteries

A strategy to achieve high loading and high energy density Li-S batteries

Flexible and Self-Supported Sulfur Cathode for High-Energy-Density Lithium-Sulfur Batteries

Strategies on Enabling High Areal Sulfur Loading in Lithium Sulfur Batteries

Revamping Lithium–Sulfur Batteries for High Cell‐Level Energy Density by Synergistic Utilization of Polysulfide Additives and Artificial Solid‐Electrolyte Interphase Layers

A compact 3D interconnected sulfur cathode for high-energy, high-power and long-life lithium-sulfur batteries

Enhanced Sulfur Transformation by Multifunctional FeS2/FeS/S Composites for High‐Volumetric Capacity Cathodes in Lithium–Sulfur Batteries

High-Performance Lithium–Sulfur Batteries with a Cost-Effective Carbon Paper Electrode and High Sulfur-Loading

(Invited) High Lithium Sulfide-Loading Electrode for Practical Li/S Cells

Atomic Interlamellar Ion Path in High Sulfur Content Lithium‐Montmorillonite Host Enables High‐Rate and Stable Lithium–Sulfur Battery

Electrode Design with Integration of High Tortuosity and Sulfur-Philicity for High-Performance Lithium-Sulfur Battery

Regulation of carbon distribution to construct high-sulfur-content cathode in lithium–sulfur batteries

Cathode Design and Evaluation for the High-Sulfur-Loading, Lean-Electrolyte Lithium–Sulfur Battery

Promoting the Transformation of Li 2 S 2 to Li 2 S : Significantly Increasing Utilization of Active Materials for High-Sulfur-Loading Li – S Batteries

A Long-Life, High-Rate Lithium/sulfur Cell: a Multifaceted Approach to Enhancing Cell Performance.

Advances in High Sulfur Loading Cathodes for Practical Lithium‐Sulfur Batteries

New approaches for high energy density lithium-sulfur battery cathodes

Low Tortuosity and Reinforced Concrete Type Ultra‐Thick Electrode for Practical Lithium–Sulfur Batteries