Abstract:OBJECTIVETo evaluate the wear intensity and surface roughness of occlusal veneers on premolars made of microhybrid composite resin or two kinds of ceramics in vitro after the thermocycling and cyclic mechanical loading tests.METHODSIn the study,24 fresh extracted human premolars without root canal treatment were prepared (cusps reduction of 1.5 mm in thickness to simulate middle to severe tooth wear, the inclinations of cusps were 20°). The prepared teeth were restored with occlusal veneers made of three different materials: microhybrid composite, heat-pressed lithium disilicate ceramic and computer-aided design/computer-aided manufacturing (CAD/CAM) lithium disilicate ceramic in the thickness of 1.5 mm. The occlusal veneers were cemented with resin cement. The specimens were fatigued using the thermocycling and cyclic mechanical loading tests after being stored in water for 72 h. The wear of specimens was measured using gypsum replicas and 3D laser scanner before and after the thermocycling and cyclic mechanical loading tests and the mean lost distance (mm) was used to indicate the level of wear. The surfaces of occlusal contact area were observed and the surface roughness was recorded using 3D laser scanning confocal microscope before and after the fatigue test. Differences between the groups were compared using ONE-way ANOVA(P<0.05).RESULTSAll the specimens successfully survived after the thermocycling and cyclic mechanical loading tests. The mean wear of microhybrid composite group, heat-pressed lithium disilicate ceramic group, and CAD/CAM lithium disilicate ceramic group was (-0.13±0.03) mm, (-0.05±0.01) mm and (-0.05±0.01) mm, the wear of microhybrid composite was significantly higher than the two ceramic groups(P<0.001).The mean surface roughness(Ra)before the fatigue test was(1.24±0.20) μm, (0.75±0.09) μm, (0.73±0.14) μm and it became (1.81±0.24) μm, (1.53±0.26) μm and (1.77±0.23) μm after the test . Before the fatigue test, the surface roughness of microhybrid composite was significantly higher than the two ceramic groups(P<0.001) and after the test, the surface roughness of heat-pressed lithium disilicate ceramic was significantly lower than microhybrid composite(P=0.005) and CAD/CAM lithium disilicate ceramic (P=0.010).CONCLUSIONFrom the view of wear speed, microhybrid composite was significantly higher than the two kinds of ceramics, but it was similar to enamel when the opposing tooth was natural. The surface roughness before the themocycling and cyclic mechanical loading test of microhybrid composite was significantly higher than that of the two ceramic groups. After the test, the surface roughness of heat-pressed ceramic was significantly lower than that of the other two groups. From the view of surface roughness, heat-pressed ceramic has more advantage.

Mechanical behavior of CAD/CAM occlusal ceramic reconstruction assessed by digital color holography.

Analysis of computerized aided designed and manufactured dental occlusal ceramics with multi-wavelength digital holography

Esthetic evaluation of Cerec 3D anterior ceramic veneers

Numeric simulation of occlusal interferences in molars restored with ultrathin occlusal veneers

A Review on Optical Methods to Assess Dental Behavior under Stress

The effect of dental restoration geometry and material properties on biomechanical behaviour of a treated molar tooth: A 3D finite element analysis

In vitro performance and fracture resistance of novel CAD/CAM ceramic molar crowns loaded on implants and human teeth

Effect of preparation design on fracture resistance of molars restored with occlusal veneers of different CAD-CAM materials: an in vitro study

Comparison of Fracture Load and Surface Wear of Microhybrid Composite and Ceramic Occlusal Veneers

Marginal adaptation and fracture resistance of milled and 3D-printed CAD/CAM hybrid dental crown materials with various occlusal thicknesses

The Influence of a Novel, Crenelated Design of CAD-CAM Ceramic Veneers on the Debonding Strength

Evaluation of the color reproducibility of all-ceramic restorations fabricated by the digital veneering method

Accuracy of Occlusal Contacts of All-Ceramic Single Crowns Designed by Virtual Articulators from a CAD/CAM System: A Preliminary Evaluation.

On the Mechanical Properties of Hybrid Dental Materials for CAD/CAM Restorations

Stress distribution around dental implants, generated by six different ceramic materials for unitary restoration: An experimental photoelastic study

Digital light printing of zirconia/resin composite material with biomimetic graded design for dental application

3-D Finite Element Analysis of MC CAD/CAM All-Ceramic Crown

Repair of fractured metal-ceramic restoration using CAD/CAM technologies. Case report

[Wear Intensity and Surface Roughness of Microhybrid Composite and Ceramic Occlusal Veneers on Premolars after the Thermocycling and Cyclic Mechanical Loading Tests].

Microstructural investigation of hybrid CAD/CAM restorative dental materials by micro-CT and SEM

Three-dimensional Analysis of the Relationship Between the Structure of Maxillary Central Incisor and the Preparation of Dental All-Ceramic