Abstract:Recently, sodium ion batteries (NIBs) gained increasing attention, because of its abundant reserves and relatively even geological distribution. However, the development of NIBs is greatly hampered because of the lack of appropriate active materials for both cathodes and anodes. Since the Na ion is ca. 55% larger than the Li ion, finding suitable host materials with sufficiently large interstitial space to accommodate sodium ions and to allow reversible and rapid ion insertion and extraction is very difficult. NASICON-type Na3V2(PO4)3 has recently been considered as a prospective cathode material for NIBs, because of its highly covalent 3D framework crystalline structure, high energy density (~400 Wh/kg) and good thermal stability. For anode materials, disordered carbon is particularly attractive because of their large interlayer distance and disordered structure that could accommodate sodium ions. Here, we briefly present porous carbon based electrodes for NIBs with excellent rate performance: (1) Carbon-coated nanosized Na3V2(PO4)3 embedded in the porous carbon matrix (abbreviated as CC-NVP@PCM); (2) Nitrogen-doped activated porous carbon fibers (ACFs); (3)Flexible free-standing porous carbon nanofibers (P-CNFs) with three-dimensional (3D) interconnected structure. The CC-NVP@PCM was prepared by using a facile soft-chemistry based method with post heat-treatment. It shows high rate performance (44 mAhg-1at 200C ). This ultrahigh rate performance is comparable to that of supercapacitor, but with much higher energy density. The ACFs were synthesized by pyrolysis of Ppy nanofiber precursor. It shows excellent capacity retention and extraordinary rate performance. The reversible capacity at 0.05 Ag-1 is 296 mAhg-1 and could still maintain as 72 mAg-1 at a current of 10 Ag-1. In case of the P-CNFs electrode prepared by electrospinning, it delivers a reversible capacity of 266 mAh.g-1 after 100 cycles at 0.2C, corresponding to 80.3 % of the initial charge capacity. When cycled at a current density as high as 500 mAg-1 (2C), it still delivers a reversible capacity of ~140 mAh.g-1after 1000 cycles. The improvement of electrochemical performance of these porous carbon based electrodes for NIBs is attributed to the special design and porous structure, which confined a variety of advantages: hierarchical porous channels enabling short transport length for ions and electrons, carbon coated structure resulting in low resistances, good mechanical properties leading to the excellent morphology stability.

Sodium-Ion Batteries: Improving the Rate Capability of 3d Interconnected Carbon Nanofibers Thin Film by Boron, Nitrogen Dual-Doping

Engineering Capacitive Contribution in Nitrogen-Doped Carbon Nanofiber Films Enabling High Performance Sodium Storage

In Situ Fabrication of Three-Dimensional Nitrogen and Boron Co-Doped Porous Carbon Nanofibers for High Performance Lithium-Ion Batteries

Constructing Active BN Sites in Carbon Nanosheets for High-Capacity and Fast Charging Toward Potassium Ion Storage

Sodium storage behavior and long cycle stability of boron-doped carbon nanofibers for sodium-ion battery anodes

High-Performance Sodium-Ion Batteries Based on Nitrogen-Doped Mesoporous Carbon Spheres with Ultrathin Nanosheets.

Multi-scale structure optimization of boron-doped hard carbon nanospheres boosting plateau capacity for high performance sodium ion battery

Multi-scale structure optimization of boron-doped hard carbon nanospheres boosting the plateau capacity for high performance sodium ion batteries

Nitrogen and Fluorine Dual Doping of Soft Carbon Nanofibers as Advanced Anode for Potassium Ion Batteries

Boosting Fast Sodium Ion Storage by Synergistic Effect of Heterointerface Engineering and Nitrogen Doping Porous Carbon Nanofibers (Small 13/2022)

Sodium/Potassium‐Ion Batteries: Boosting the Rate Capability and Cycle Life by Combining Morphology, Defect and Structure Engineering

Electrodes for Sodium-Ion Batteries with Excellent Rate Performance Using Porous Carbon Networks

Nitrogen-doped 3D nanocarbon with nanopore defects as high-capacity and stable anode materials for sodium/lithium-ion batteries

Superior Sodium Storage in 3D Interconnected Nitrogen and Oxygen Dual-Doped Carbon Network.

Structure engineering and heteroatom doping-enabled high-energy and fast-charging dual-ion batteries

A Flexible Sulfur-Enriched Nitrogen Doped Multichannel Hollow Carbon Nanofibers Film for High Performance Sodium Storage.

Advanced core-shell hollow carbon nanofibers for ion and electron accessibility in sodium ion batteries

Design Nitrogen (N) and Sulfur (S) Co-Doped 3D Graphene Network Architectures for High-Performance Sodium Storage.

Nanoframes@CNT Beads‐on‐a‐String Structures: Toward an Advanced High‐Stable Sodium‐Ion Full Battery

Tailoring 2D Heteroatom‐Doped Carbon Nanosheets with Dominated Pseudocapacitive Behaviors Enabling Fast and High‐Performance Sodium Storage

Improved Rate Capability of Si-C Composite Anodes by Boron Doping for Lithium-Ion Batteries