Abstract:Background: Although few methods are used to estimate polyethylene liner wear from radiographs of total hip replacements, there is no consensus with regard to the accuracy of these methods. Highly cross-linked polyethylene (XLPE) is reported to have low rates of linear wear in the literature. However, there are not reports about wear rate of ceramic head in hxple cup at 5 years postoperatively, evaluated by Dorr method. We evaluated the wear rate of HXPLE, within the first five years after implantation using manual techniques of Dorr. Material and methods: We evaluated 143 patients (93 males and 50 females) with one design of uncemented acetabular component, a 40-mm (77 hips) or 44-mm (66 hips) ceramic femoral head and the annealed highly cross-linked crossfire polyethylene (X3) insert used in combination with Secur-Fit Advanced stems at a mean follow-up of 5 years. Selection of these femoral heads was based on several factors, including the perceived risk of dislocation, the outer diameter size of the acetabular component, and liner availability. Measurements of linear wear were performed by experienced surgeons with Dorr method and analyzed using the first-to-last method. Standard radiographs were used to detect periprosthetic osteolysis. Clinical records were used to determine all demographic data (age, height, weight, gender, months of follow-up, etc.). Results: For the entire cohort, the median linear wear rate was 0.0438 mm per year at 5 years and there was no any revision due to loosening, no liner fracture, and no patient with symptomatic corrosion. The head size was selected intraoperatively based on the size of the acetabular component and presumed risk of dislocation. There was no hip with pelvic or femoral osteolysis. The median linear wear rate was 0.0461 mm (±0.0183) and 0.0409mm (±0.0118), respectively, at head diameters of 40 and 44 mm. We found no association between femoral head size and the linear wear rate. This sentence can be excluded from here CONCLUSIONS: This acetabular component and HXLPEs with large ceramic heads had low rates of linear wear. Large ceramic femoral heads did not lead to liner fracture, loosening, or symptomatic trunnion corrosion in this patient population. However, we recommend longer clinical follow-up studies and caution in the routine use of larger ceramic femoral heads in other, younger patient populations. Key words: Ceramic femoral heads, Highly cross-linked polyethylene, Large heads, Total hip arthroplasty.

Medium-term results of ceramic-on-polyethylene Zweymüller-Plus total hip arthroplasty.

Total hip arthroplasties in 190 cases: follow-up study]

Long-Term Effectiveness of Total Hip Replacement with the Collum Femoris Preserving Prosthesis

Intermediate outcomes of alumina-on-alumina bearing total hip arthroplastyTotal arthroplasty, replacement, hip; Ceramic; Frictione; Prostheses and implants

[Revision Hip Arthroplasty with the Cementless Prosthesis: 4 Years Follow-Up Study].

[Intermediate Outcomes of Alumina-on-alumina Bearing Total Hip Arthroplasty].

Excellent Results of Large-Diameter Ceramic-On-Ceramic Bearings in Total Hip Arthroplasty at Minimum Ten-Year Follow-Up

Why Are Contemporary Primary Ceramic-on-Highly Crosslinked Polyethylene Total Hip Arthroplasties Failing? An Analysis of Over 5,500 Cases

Ceramic-on-ceramic vs metal-on-crosslink polyethylene in a fully hydroxyapatite-coated total hip arthroplasty: Survivorship, complications and long-term results

Long-term follow-up of total hip arthroplasty using polyethylene-ceramic composite (sandwich) liner

A multi-center retrospective comparative study of third generation Ceramic-on- Ceramic total hip arthroplasty in patients younger than 45 years with or without the sandwich liner: A ten-year minimum

Ceramic femoral head in highly cross-linked polyethylene cup. 5 year results of a randomized trial

Pure Alumina Bearings with Cementless Stems Versus Sandwich Bearings with Cemented Stems in Total Hip Arthroplasty.

Excellent mid-term outcomes with a hemispheric titanium porous-coated acetabular component for total hip arthroplasty: 7-10 year follow-up

Femoral Component Revision Using Extensively Porous-Coated Cementless Stem.

LONG TERM DATA CONCERNING THE USE OF ALL ALUMINA IN TOTAL HIP REPLACEMENTS: SPECIAL INTEREST IN YOUNG AGE POPULATION.

Preliminary Clinical And Radiographic Results Of Large Ceramic Heads On Highly Cross-Linked Polyethylene

Long-term Results of Total Hip Arthroplasty with Chinese Porous Coated Anatomic Prothesis: a 11-to 17-Year Follow-Up Study

No Revisions Attributable to Wear of Highly Cross-Linked Polyethylene Liners: A Long-Term Follow-Up Study

[Mid-Term Follow-Up Study of Hip Arthroplasty for Internal Fixation Failure of Femoral Intertrochanteric Fractures in the Elderly].

Measurement of polyethylene wear and its clinical significance in total hip arthroplasty