Abstract:Objective: To analyze the wear debris characteristics ofcarbon-based nano- multilayer coatings on Ti(6)Al(4)V alloys and compared with the cobalt chromium molybdenum alloy (CoCrMo) femoral head to evaluate the friction and wear performance of the new coated femoral head. Methods: Three groups were set up in the wear simulation experiment according to the type of femoral head. Group A: imported Cobalt-Chromium-Molybdenum alloy femoral head (CoCrMo); group B: Titanium alloy femoral head (Ti(6)Al(4)V) with carbon-based nano-multilayer coatings; group C: domestic Cobalt-Chromium-Molybdenum alloy femoral head (CoCrMo). All heads were jointed with an ultra-high molecular weight polyethylene (UHMWPE) acetabular cup. Serum samples were collected and stored in the hip joint simulator. After the sample has been digested and diluted, it was filtered through 5 μm, 1.2 μm and 0.4 μm filters, and the filter paper was collected for testing. Scanning electron microscope (SEM) was used to randomly select regions on the filter to obtain images of wear debris. Energy dispersive X-ray spectroscopy (EDS) was used to determine the elemental type of the particle and to eliminate possible contamination. The composition and structure of the abrasive chips were measured using Fourier transform infrared spectrometer (FTIR). The parameters related to the wear debris includingparticle size, shape, number and volume were calculated. The differences in correlation parameters between the groups were compared to evaluate the friction and wear properties of the new coated joints. Results: The main component of the wear debris produced was UHMWPE, and the particle size was mostly below 1 μm. The submicron particle ratio of group B was 49.4%, which was significantly lower than that of the group A and C (75% and 60%, respectively; χ(2)=66.032, 31.754, both P<0.017). The shape was mainly round, and there was no statistical difference between the groups (χ(2)=0.590, P=0.744). The number of particles in group B was significantly less than that of group C on all filters (t=9.960, 8.019, 5.790, all P<0.01), and less than group A on the 0.4 μm filter (t=7.810, P=0.000). Conclusion: The frictional wear performance of the new carbon-based nano-multilayer coatings femoral head is significantly better than that of the domestic femoral head, and even partially exceeds the imported femoral head level, which helps to reduce the production of particles and prevent osteolysis and aseptic loosening induced by UHMWPE particles.

Effects of Carbon Addition on Wear Mechanisms of CoCrMo Metal-on-metal Hip Joint Bearings.

Effect of Carbon Content on Wear Behavior of Ni-Co-Cr-Mo-Cu Alloy

Mechanical Tests, Wear Simulation and Wear Particle Analysis of Carbon-Based Nanomultilayer Coatings on Ti6Al4V Alloys As Hip Prostheses

Effects of Sigma Phase and Carbide on the Wear Behavior of CoCrMo Alloys in Hanks' Solution

Unveiling Microstructural Evolution and Enhanced Wear Resistance of Co37Cr28Ni31Al2Ti2 Multicomponent Alloy Via High-Carbon Addition

Improving biotribological properties and corrosion resistance of CoCrMo alloy via a Cr-GLC nanocomposite film in simulated body fluids

[Five Million Wear Simulation and Particle Analysis of Carbon-Based Nano-Multilayer Coatings Titanium Alloy Femoral Head].

Effects of Microstructures on the Sliding Behavior of Hot-Pressed CoCrMo Alloys

Investigation into Reciprocating Dry Sliding Friction and Wear Properties of Bulk CoCrFeNiMo High Entropy Alloys Fabricated by Spark Plasma Sintering and Subsequent Cold Rolling Processes: Role of Mo Element Concentration

A study on tribological properties of textured Co-Cr-Mo alloy for artificial hip joints

Performance of CoCrMo Alloy with Me-Doped DLC Coatings Prepared by a Magnetron Sputtering Method

Effect of Ni, W and Mo on the Microstructure, Phases and High-Temperature Sliding Wear Performance of CoCr Matrix Alloys

Friction and Wear of Diamond-Like Carbon Film Deposited on Cocrmo Alloy under Different Lubrication

Effect of Carbon on the Microstructure and Sliding Wear Performance of CoCrMo Matrix Composites from Room Temperature to 1000 °C

Tribo‐corrosion Mechanisms and Electromechanical Behaviours for Metal Implants Materials of CoCrMo, Ti6Al4V and Ti15Mo Alloys

Influence of carbon and nitrogen addition on microstructure and hot deformation behavior of biomedical Co-Cr-Mo alloy

The acting wear mechanisms on metal-on-metal hip joint bearings: in vitro results

Predicting the Metal Ion Release From CoCrMo Alloy–UHMWPE Tribocorrosion Contacts

Effects of Alloy Additions on the Fatigue Properties of Cast Co-Cr-Mo Alloy Used for Surgical Implants

Effect of aqueous solution and load on the formation of DLC transfer layer against Co-Cr-Mo for joint prosthesis.

In Vitro Analysis of Wearing of Hip Joint Prostheses Composed of Different Contact Materials