Abstract:Perovskite solar cells based on the inorganic/organic hybrid perovskite have attracted increasing attention over the past 3 years. Many studies have been done in this area. Controling the morphology of the perovskite film is an effective way to improve the photoelectric conversion efficiency of the devices. In our reserch, we studied the influence of structure and morphology of perovskite films on the performance of the organic-inorganic hybrid perovskite solar cells which prepared by a sequential deposition method. Mesoporous TiO2 scaffold were introduced as electron collecting layer. Lead iodide (PbI2) was then spin cast on the TiO2 scaffold. The PbI2 subsequently transformed into the perovskite (CH3NH3PbI3) by dipping the TiO2/PbI2 film into a solution of CH3NH3I. We studied the difference between the PbI2 film with or without drying under room temperature after spin-coating. Through drying under room temperature, larger pores formed in the PbI2 film. While without drying under room temperature, smaller and shallower pores formed in the PbI2 film. The results show that larger pores in PbI2 film leads to more complete transformation of PbI2 to CH3NH3PbI3 and larger CH3NH3PbI3 particles. CH3NH3PbI3 films were prepared with three different processes: (a) direct dipping the PbI2 film with smaller pores into the CH3NH3I solution; (b) direct dipping the PbI2 with larger pores into the CH3NH3I solution; (c) dipping the PbI2 with larger pores into the CH3NH3I solution after pre-wetting. The resulting CH3NH3PbI3 films were studied with SEM, UV-vis absorption spectrum and XRD. The particles size of the CH3NH3PbI3 are 150, 250 and 350 rim for process (a), (b) and (c) respectively. CH3NH3PbI3 films fabricated through process (a) show insufficient absorption due to the insufficient transformation of the PbI2. The pre-wetting procedure leads to slower reaction result in larger CH3NH3PbI3 particle size. Devices with proper size of CH3NH3PbI3 particles show the highest photoelectric conversion efficiency. An efficiency of 13.5% was achieved with a J(sc) of 17.8 mA/cm(2), a V-oc of 1.05 V and a FF of 72.5%.

Influence of Hydration Water on CH3NH3PbI3 Perovskite Films Prepared Through One-Step Procedure.

First-Principles Calculations of Graphene-Coated CH3NH3PbI3 Toward Stable Perovskite Solar Cells in Humid Environments

Influence of Structure and Morphology of Perovskite Films on the Performance of Perovskite Solar Cells

Microstructure Modulation Of The Ch3nh3pbi3 Layer In Perovskite Solar Cells By 2-Propanol Pre-Wetting And Annealing In A Spray-Assisted Solution Process

Optimization of the Photoelectric Properties and Photo-Stability of CH3NH3PbBrXI3-X Films for Efficient Planar Perovskite Solar Cells

Moisture Annealing Effect on CH3NH3PbI3 Films Deposited by Solvent Engineering Method

Influence of Drying Temperature on Morphology of MAPbI3 Thin Films and the Performance of Solar Cells

Doped Manipulation of Photoluminescence and Carrier Lifetime from CH3NH3PbI3 Perovskite Thin Films

Growth of Compact CH3NH3PbI3 Thin Films Governed by the Crystallization in PbI2 Matrix for Efficient Planar Perovskite Solar Cells.

Influence of drying temperature on morphology of MAPbI$_3$ thin films and the performance of solar cells

Enhanced Sensitivity of Grain Sizes to Precursor Stoichiometry Enables High-Quality CH3NH3PbI3 Films for Efficient Perovskite Solar Cells

Controlled Crystallization of CH3NH3PbI3 Films for Perovskite Solar Cells by Various PbI2(X) Complexes

A Compact And Smooth Ch3nh3pbi3 Film: Investigation Of Solvent Sorts And Concentrations Of Ch3nh3i Towards Highly Efficient Perovskite Solar Cells

Photostability and Moisture Stability of Ch3nh3pbi3-Based Solar Cells by Ethyl Cellulose

A general non-CH3NH3X (X = I, Br) one-step deposition of CH3NH3PbX3 perovskite for high performance solar cells

Enhanced Performance of Perovskite CH3NH3PbI3 Solar Cell by Using CH3NH3I as Additive in Sequential Deposition.

Precisely Controlled Hydration Water for Performance Improvement of Organic–Inorganic Perovskite Solar Cells

Efficient and Reproducible CH3NH3PbI3 Perovskite Layer Prepared Using a Binary Solvent Containing a Cyclic Urea Additive.

Morphology and surface analyses for CH3NH3PbI3 perovskite thin films treated with versatile solvent-antisolvent vapors

Intermediate Phase Intermolecular Exchange Triggered Defect Elimination in CH3NH3PbI3 Toward Room-Temperature Fabrication of Efficient Perovskite Solar Cells.

Preparation of CH3NH3PbI3 Thin Films for Solar Cells Via Vapor Transfer Method