Abstract:The limitation of poor mechanical stability and difficulties in printing electrically conductive components can be overcome owing to the recent introduction of nanotechnology into the field of additive manufacturing (AM) and the consequent development of nonconventional polymer nanocomposites suitable for 3D printing. In the present work, different weight percentages (up to 6 wt % in total) of carbon-based nanostructures-multiwalled carbon nanotubes (MWCNTs), graphene nanoplatelets (GNPs), and a combination of both fillers (MWCNTs/GNPs)-were incorporated into poly(lactic) acid (PLA, Ingeo™) in an attempt to overcome several limitations of conventional 3D manufacturing based on insulating materials. Solution blending and melt mixing were the two fabrication methods adopted for preparation of the samples under test. A comparison of the morphological, rheological, and electrical properties of the resulting nanocomposites was carried out. Moreover, for the same weight concentrations, the influence of physical and geometrical features (i.e., functionalization and aspect ratio) of the embedded fillers was also investigated. Rheological methods were applied to control the quality of fillers dispersion in PLA matrix. The rheological percolation threshold was considered as reference in order to evaluate the internal structure of nanodispersions. TEM visualization, combined with rheological characterizations, was used for efficient control of the nanofiller dispersion. DC characterization revealed that lower electrical percolation thresholds and higher values of electrical conductivity were achieved using fillers with a larger aspect ratio and melt mixing, respectively. Moreover, given the possibility of obtaining complex and appropriate shapes for electromagnetic compatibility (EC) applications, electromagnetic (EM) response of the nanocomposites at the highest filler concentration was investigated in GHz and THz regions. It was found that the electromagnetic shielding efficiency (EMI) of nanocomposites strongly depended on the aspect ratio of the nanofillers, whereas the type of processing technique did not have a significant effect. Therefore, a careful choice of methods and materials must be made to address the final application for which these materials and further 3D printed architectures are designed.

Shear induced alignment of short nanofibers in 3D printed polymer composites.

Development of Mechanically Enhanced Polycaprolactone Composites by a Functionalized Titanate Nanofiller for Melt Electrowriting in 3D Printing.

Experimental and Theoretical Studies on 3D Printed Short and Continuous Carbon Fiber Hybrid Reinforced Composites

3D printing-enabled self-assembling β-nucleating agent alignment: Structural evolution and mechanical performances

The Effects of Shear Stress on the Micromechanical Properties of 3D Printable Biopolymer Nanocomposites using a Custom‐Designed Extrusion Based 3D Printer

Direct Ink Writing for High-Efficiency Microwave Attenuation with Nanofibers Alignment

Enhancing shear strength in 3D printed single lap composite joints: A multi‐faceted exploration of GNP integration, print orientation, utilizing artificial neural networks, and dynamic analysis

Morphological, Rheological and Electromagnetic Properties of Nanocarbon/Poly(lactic) Acid for 3D Printing: Solution Blending vs. Melt Mixing

Highly loaded carbon fiber filaments for 3D‐printed composites

In Situ Electrical Network Activation and Deactivation in Short Carbon Fiber Composites via 3D Printing

Processing Dynamics of 3D-Printed Carbon Nanotubes-Epoxy Composites

3D Printing-Induced Hierarchically Aligned Nanocomposites With Exceptional Multidirectional Strain Sensing Performance

Investigation on the mechanical properties of 3D printed hybrid continuous fiber-filled composite considering influence of interfaces

Shear and Tensile Behaviors of Fiber-Reinforced Resin Matrix Composites Printed by the FDM Technology

Effect of Filler Alignment on Piezo-Resistive and Mechanical Properties of Carbon Nanotube Composites

Bioinspired composites reinforced with ordered steel fibers produced via a magnetically assisted 3D printing process

The Influence of Nanoparticle Dispersions on Mechanical and Thermal Properties of Polymer Nanocomposites using SLA 3D Printing

Shape memory and mechanical characterization of polylactic acid wood composite fabricated by fused filament fabrication 4D printing technology

Essential Nanostructure Parameters to Govern Reinforcement and Functionality of Poly(lactic) Acid Nanocomposites with Graphene and Carbon Nanotubes for 3D Printing Application

Manufacturing of bioinspired Bouligand structures using ultrasound assisted 3D printing

Enhanced thermal conductivity of alumina and carbon fibre filled composites by 3-D printing