Abstract:Function, failure, and remodeling of the intervertebral disc are all related to the stress and strain fields in the tissue and may be calculated by finite element models with accurate material properties, realistic geometry, and appropriate boundary conditions. There is no comprehensive study in the literature investigating the shear material properties of the annulus fibrosus. This study obtained shear material properties of the annulus fibrosus and tested the hypothesis that these properties are affected by the amplitude and frequency of shearing, applied compressive stress, and degenerative state of the tissue. Cylindrical specimens with an axial orientation from seven nondegenerated and six degenerated discs were tested in torsional shear under dynamic and static conditions. Frequency sweep experiments over a physiological range of frequencies (0.1-100 rad/sec) at a shear strain amplitude of 0.05 rad were performed under three different axial compressive stresses (17.5, 25, and 35 kPa). At the largest compressive stress, shear strain sweep experiments (strain amplitude range: 0.005-0.15 rad at a frequency of 5 rad/sec) and transient stress-relaxation tests (shear strain range: 0.02-0.15 rad) were performed. The annulus fibrosus material was less stiff and more dissipative at larger shear strain amplitudes, stiffer at higher frequencies of oscillation, and stiffer and less dissipative at larger axial compressive stresses. The dynamic shear modulus, /G*/, had values ranging from 100 to 400 kPa, depending on the experimental condition and degenerative level. The shear behavior was also predominantly elastic, with values for the tangent of the phase angle (tandelta) ranging from 0.1 to 0.7. The annulus material also became stiffer and more dissipative with degenerative grade; however, this was not statistically significant. The results indicated that nonlinearities, compression/shear coupling, intrinsic viscoelasticity, and, to a lesser degree, degeneration all affect the shear material behavior of the annulus fibrosus, with important implications for load-carriage mechanisms in the intervertebral disc. These material complexities should be considered when choosing material constants for finite element models.

Mechanical Characterization of Non-degraded Porcine Annulus Fibrosus Material Properties

How Static and Cyclic Loading Affect the Mechanical Properties of the Porcine Annulus Fibrosus

Shear mechanical properties of human lumbar annulus fibrosus

Mechanically Conditioned Multilayered Angle-Ply Collagen Scaffolds Promote Annulus Fibrosus Regeneration

Ex vivo biomechanical evaluation of Acute lumbar endplate injury and comparison to annulus fibrosus injury in a rat model

The effect of compressive loading rate on annulus fibrosus strength following endplate fracture

Ex-vivo biomechanical evaluation of the application of a novel annulus closure device to closure of annulus fibrosus

Fracture of porcine aorta. Part 2: FEM modelling and inverse parameter identification

A novel finite element model of the ovine lumbar intervertebral disc with anisotropic hyperelastic material properties

Mechanical properties of spinal cord grey matter and white matter in confined compression

Re-examination of the mechanical anisotropy of porcine thoracic aorta by uniaxial tensile tests

Experimentally Dissociating the Acute Mechanisms of Endplate Fracture Lesions and Schmorl's Node Injuries Using a Porcine Cervical Spine Model

On the experimental determination of some mechanical properties of porcine periodontal ligament

An Approach to Quantify Anisotropic Multiaxial Failure of the Annulus Fibrosus

Experimental and numerical study on the mechanical properties of cortical and spongy cranial bone of 8-week-old porcines at different strain rates

Injectable Cell-Laden Nanofibrous Matrix for Treating Annulus Fibrosus Defects in Porcine Model: An Organ Culture Study

Comparison between the dynamic and initial creep response of porcine and human lumbar intervertebral discs

Experimental and Numerical Evaluations of the Viscoelastic Mechanical Behavior of Arterial Tissue

Material Parameter Identification of the Proximal and Distal Segments of the Porcine Thoracic Aorta Based on ECG-gated CT Angiography

Characterization of the mechanical properties for cranial bones of 8-week-old piglets: the effect of strain rate and region

Regional Variations in the Cellular, Biochemical, and Biomechanical Characteristics of Rabbit Annulus Fibrosus.