Abstract:Particle size and content of RDX are the two main factors that affect the burning stability of RDX-based propellants. However, these effects and the corresponding mechanisms are still controversial. In this work, we investigated the physicochemical processes during burning and the corresponding mechanisms through the technologies of structure compactness analysis on the base of voidage measurement and theoretical interfacial area estimation, apparent burning rate measurement using closed vessel (CV) and extinguished burning surface characterization relying on interrupted closed vessel (ICV) and scanning electron microscope (SEM). The results indicate that the voidage increased with the increase of RDX content and particle size due to the increasing interfacial area and increasing interface gap size, respectively. The apparent burning rate increased with the increase of RDX particle size because of the decreasing RDX specific surface area on the burning surface, which could decrease the heat absorbing rates of the melting and evaporation processes of RDX in the condensed phase. Similarly, the apparent burning rate decreased with the increase of RDX content at pressures lower than around 55 MPa due to the increasing RDX specific surface area. Whereas, an opposite trend could be observed at pressures higher than around 55 MPa, which was attributed to the increasing heat feedback from the gas phase as the result of the increasing propellant energy. For propellants containing very coarse RDX particles, such as 97.8 and 199.4 μm average size, the apparent burning rate increased stably with a flat extinguished surface at pressures lower than around 30 MPa, while increased sharply above around 30 MPa with the extinguished surface becoming more and more rugged as the pressure increased. In addition, the turning degree of <em>u</em>-<em>p</em> curve increased with the increase of coarse RDX content and particle size, and could be reduced by improving the structure compactness.

Air explosion characteristics of a novel TiH 2 /RDX composite explosive

Shock Response of 1,3,5-Trinitroperhydro-1,3,5-triazine (RDX): the C-N Bond Scission Studied by Molecular Dynamics Simulations

Detonation Characteristics of RDX-Liquid Fuel-Air Three-Phase System

Effect of low-concentration RDX dust on solid–liquid mixed fuel characteristics

Preparation, characterization, and investigation of thermal behavior of improved HMX and RDX through coating by TNT

Preparation and Safety of Well-Dispersed RDX Particles Coated with Cured HTPB

Internal Explosion Performance of RDX@Nano-B Composite Explosives

Deflagration to detonation transition in weakly confined conditions for a type of potentially novel green primary explosive: Al/Fe2O3/RDX hybrid nanocomposites

Explosion temperature mapping of emulsion explosives containing TiH2 powders with the two-color pyrometer technique

Molecular Dynamics Simulations of the Thermal Decomposition of RDX/HTPB Explosives

A Method to Investigate the Confined Explosion of Thermobaric and Enhanced Blast Explosives

Influence of Al Content and Surrounding Medium on the Energy Output of Cyclotrimethylenetrinitramine (rdx)/al/wax Explosives

Effects of Sn-containing intermetallic compounds on the thermal decomposition and ignition properties of RDX and TKX-50

Research of detonation products of RDX/Al from the perspective of composition

Effects of particle size and content of RDX on burning stability of RDX-based propellants

The effect of Mg(BH4)2 on the energy characteristics of RDX based aluminized explosives

ReaxFF molecular dynamics simulations on thermal decomposition of RDX-based CMDB propellants

Theoretical calculation into the effect of molar ratio on the structures, stability, mechanical properties and detonation performance of 1,3,5,7-tetranitro-1,3,5,7-tetrazocane/ 1,3,5-trinitro-1,3,5-triazacyco-hexane cocrystal

On weak influence of aluminum powder size on its post-detonation reaction in different time scales

Multi-scale modified nitramine crystals with conjugated structure intercalation and thin-layer catalyst coating for well-controlled energy release rate

Mechanochemical fabrication and properties of CL-20/RDX nano co/mixed crystals