Abstract:The surface quality of the continuous casting strands is closely related to the initial solidification of liquid steel in the vicinity of the mold meniscus, and thus the clear understanding of the behavior of molten steel initial solidification would be of great importance for the control of the quality of final slab. With the development of the mold simulator techniques, the complex interrelationship between the solidified shell surface profile, heat flux, shell thickness, mold level fluctuation, and the infiltrated slag film was well illustrated in our previous study. As the second part, this article investigated the effect of the mold oscillation frequency, stroke, and mold level fluctuation on the initial solidification of the molten steel through the conduction of five different experiments. Results suggested that in the case of the stable mold level, the oscillation marks (OMs) exhibit equally spaced horizon depressions on the shell surface, where the heat flux at the meniscus area raises rapidly during negative strip time (NST) period and the presence of each OMs on the shell surface is corresponding to a peak value of the heat flux variation rate. Otherwise, the shell surface is poorly defined by the existence of wave-type defects, such as ripples or deep depressions, and the heat flux variation is irregular during NST period. The rising of the mold level leads to the longer-pitch and deeper OMs formation; conversely, the falling of mold level introduces shorter-pitch and shallower OMs. With the increase of the mold oscillation frequency, the average value of the low-frequency heat flux at the meniscus increases; however, it decreases when the mold oscillation stroke increases. Additionally, the variation amplitude of the high-frequency temperature and the high-frequency heat flux decreases with the increase of the oscillation frequency and the reduction of the oscillation stroke.

An Investigation of the Mold-Flux Performance for the Casting of Cr12MoV Steel Using a Mold Simulator Technique

Analysis of Longitudinal Cracking and Mold Flux Optimization in High-Speed Continuous Casting of Hyper-Peritectic Steel Thin Slabs

Influence of Mineralogical Structure of Mold Flux Film on Heat Transfer in Mold during Continuous Casting of Peritectic Steel

Development of Mold Flux for Continuous Casting of High-Carbon Steel Bloom

Continuous Casting Mould for Square Steel Billet Optimised by Solidification Shrinkage Simulation

Initial Solidification Behavior of Spring Steel Billet Near the Mold Corner During Continuous Casting Process

Transient flow and mold flux behavior during ultra-high speed continuous casting of billet

Melting and Flowing Behavior of Mold Flux in a Continuous Casting Billet Mold for Ultra-High Speed

Unveiling the effect of MnO/SiO2 ratios on the viscosity and structure of mold fluxes for high-Mn cryogenic steels

An in-situ investigation on the microstructure and viscosity characteristic of mold flux during slag-metal reaction process

A coupled model on fluid flow, heat transfer and solidification in continuous casting mold

Properties and structure of a new non-reactive mold flux for high-Al steel

Modeling study of EMBr effects on molten steel flow, heat transfer and solidification in a continuous casting mold

Analysis of Thermomechanical Behavior in Continuous Bloom Casting Mold

Mold Simulator Study of the Initial Solidification of Molten Steel in Continuous Casting Mold: Part II. Effects of Mold Oscillation and Mold Level Fluctuation

Simulation of the Effect of Flux Layer Thickness on the Melting Behavior of Mold Fluxes Based on the Copper Bath Method

Thickness Distributions of Mold Flux Film and Air Gap in Billet Ultra-High Speed Continuous Casting Mold Through Multiphysics Modeling

Assessment of heat transfer through mold slag film considering radiative absorption behavior of mold fluxes

Solidification and Crystallization Properties of CaO-SiO2-Na2O Based Mold Fluxes

A Review of the Melt Structure and Crystallization Behavior of Non‐Reactive Mold Flux for the Casting of Advanced High‐Strength Steels

Numerical Simulation of the Flow Field in an Ultrahigh-Speed Continuous Casting Billet Mold