Abstract:Silicon based power micro-electro-mechanical system (MEMS) applications require highspeed microrotating machinery operating stably over a large range of operating conditions. The technical barriers to achieving stable high-speed operation with micro-gas-bearings are governed by (1) stringent fabrication tolerance requirements and manufacturing repeatability, (2) structural integrity of the silicon rotors, (3) rotordynamic coupling effects due to leakage flows, (4) bearing losses and power requirements, and (5) transcritical operation and whirl instability issues. To enable high-power density the micro-turbomachinery must be run at tip speeds comparable to conventional scale turbomachinery. The rotors of the micro-gas turbines are supported by hydrostatic gas journal and hydrostatic gas thrust bearings. Dictated by fabrication constraints the location of the gas journal bearings is at the outer periphery of the rotor. The high bearing surface speeds (target nearly 10 x 10(6) mm rpm), the very low bearing aspect ratios (L/D < 0.1), and the laminar flow regime in the bearing gap (Re < 500) place these micro-bearing designs into unexplored regimes in the parameter space. A gas-bearing supported micro-air turbine was developed with the objectives of demonstrating repeatable, stable high-speed gas-bearing operation and verifying the previously developed micro-gas-bearing analytical models. The paper synthesizes and integrates the established micro-gas-bearing theories and insight gained from extensive experimental work. The characteristics of the new micro-air turbine include a four-chamber journal bearing feed system to introduce stiffness anisotropy, labyrinth seals to avoid rotordynamic coupling effects of leakage flows, a reinforced thrust bearing structural design, a redesigned turbine rotor to increase power, a symmetric feed system to avoid flow and force nonuniformity, and a new rotor micro-fabrication methodology for reduced rotor imbalance. A large number of test devices were successfully manufactured demonstrating repeatable bearing geometry. More specifically, three sets of devices with different journal bearing clearances were produced to investigate the dynamic behavior as a function of bearing geometry. Experiments were conducted to characterize the "as-fabricated" bearing geometry, the damping ratio, and the natural frequencies. Repeatable high-speed bearing operation was demonstrated using isotropic and anisotropic bearing settings reaching whirl-ratios between 20 and 40. A rotor speed of 1.7 x 10(6) rpm (equivalent to 370 m/s blade tip speed or a bearing DN number of 7 x 10(6) mm rpm) was achieved demonstrating the feasibility of MEMS-based micro-scale rotating machinery and validating key aspects of the micro-gas-bearing theory. [DOI: 10.1115/1.3123343]

Discussions on Problem Analysis and Solutions of a Micro Turbine Test

Design and Test of a 600-Kw Horizontal-Axis Tidal Current Turbine

Numerical and experimental investigation of a cooling technique of a turbocharger radial turbine

MODEL ANALYSIS AND TEST RESEARCH OF HORIZONTAL-AXIAL MARINE CURRENT TURBINE

Research on aerodynamic characteristics of two-stage axial micro air turbine spindle for small parts machining

Technical Design and Principle Test of Active Magnetic Bearings for the Turbine Compressor of Htr-10gt

Influences of main design parameters on the aerodynamic performance of a micro-radial inflow turbine

Rotor Stress and Dynamics Analysis of a High-Speed Permanent Magnet Machine for a Micro Gas Turbine Considering Multiphysics Factors

New Radial Turbine Dynamic Modelling in a Low-Temperature Adiabatic Compressed Air Energy Storage System Discharging Process

Modeling and Performance Analysis of a Dual-Shaft Counter-Rotating Gas Turbine

A Design of Simulation Experiment System for the Helium Turbine

Investigation of radial force in a high-speed miniature pump

High-Speed Operation of a Gas-Bearing Supported MEMS-Air Turbine

Study on Design of Magnetic Load Simulator

Analysis of an Air Powered Engine System Using a Multi-Stage Radial Turbine.

Numerical simulation and low speed experiment of a low partially admitted rate axial turbine for small scale organic Rankine cycle

Development of Numerical Performance Test Stand for A Kaplan Turbine

Research on the Relationships Between Blade Angles and External Characteristics of A Centimeter Scale Pneumatic Turbine

Analysis of the Rotor System of a Micro -Gas Turbine Engine Based on Finite Element Method

Improving Vibration Response of Radial Turbine in Variable Geometry Turbochargers With CFD Analysis

Numerical and Experimental Investigation on Thermohydrodynamic Performance of Turbocharger Rotor-Bearing System