Abstract:Large capacity supercritical boiler is at the leading edge of efficiency boost for thermal power plant. Water wall design is a key issue for a supercritical boiler. To ensure successful design and safe operation of water wall, studying hydraulic resistance of water is significant. Considerable work on frictional pressure drop of gas-liquid two-phase flow in tubes has been done and various correlations have been proposed to predict it. However, these correlations are restricted to particular rib geometries and flow conditions. Because of significant variations in thermo physical properties near the critical and pseudo-critical points, pressure drop at supercritical pressures is different from that at subcritical pressures. However, limited studies have been devoted to estimate hydraulic resistance of supercritical water. More work need be conducted to develop prediction method for pressure drop at supercritical pressures. Therefore, to accumulate fundamental experimental data for the design of a supercritical boiler, an experiment on hydraulic resistance of water was performed in a vertical upward rifled tube. The experiment was carried out in the high-temperature and high-pressure steam-water test loop at Xi'an Jiaotong University. Based on the experimental data, the two-phase frictional multiplier was calculated to analyze the two-phase frictional pressure drop. At low to moderate vapor quality, the two-phase frictional multiplier increases rapidly and reaches a peak. When the vapor quality exceeds a certain value, the two-phase frictional multiplier starts to decrease with increasing vapor quality. It is because the tube wall is covered by liquid film at low to moderate vapor quality. Within the high vapor quality region, the high-speed vapor tears the liquid film and the flow pattern turns to mist flow with lower frictional pressure drop. Increasing pressure decreases the two-phase frictional multiplier and when the pressure approaches the critical pressure, the multiplier is close to 1. The effect of mass flux on the multiplier is so weak that it can be neglected. At supercritical pressures, the pressure drops due to frictional resistance and flow acceleration both increase with bulk fluid enthalpy. Increasing pressure decreases the frictional pressure drop. This result is mainly attributed to pressure approaching the critical point. Frictional pressure drop is significantly affected by fluid property variations; in particular, severe density decreases with increasing bulk fluid enthalpy. Acceleration pressure drop increases with decreasing pressure and increasing heat flux. When heat flux increases, the density difference between the inlet and the outlet increases with the same mass flux, which results in a considerable acceleration pressure drop. Decreasing pressure results in a similar acceleration pressure drop variation because of the same reason. The frictional resistance coefficient was calculated to analyze the supercritical frictional pressure drop. In the large specific heat region, the frictional resistance coefficient peaks at a certain enthalpy in the vicinity of the pseudo-critical point, and increasing mass flux reduces the magnitude of the peak value.

Two-phase Critical Discharge of Initially Saturated or Subcooled Water Flowing in Sharp-Edged Tubes at High Pressure

Numerical Simulation on Heterogeneous Heat Transfer in Water at Supercritical Pressures in Inclined Upward Tubes

STUDY ON CRITICAL HEAT FLUX OF STEAM-WATER TWO-PHASE FLOW IN HELICAL COIL TUBES

Theoretical and Experimental Analyses of Two-Phase Flow Condensation Heat Transfer Inside the Horizontal Micro-Fin Tube

Theoretical study on the critical flow through a straight-edged tube

Heat Transfer Characteristic of Water at Near Critical Pressure in Circumferentially Non-Uniformly Heated Vertical Tubes

INVESTIGATION ON THE TUBE WALL TEMPERATURE AND CRITICAL HEAT FLUX FOR HIGH PRESSURE STEAM-WATER TWO-PHASE FLOW IN INTERNALLY RIBBED TUBES

Flow and Heat Transfer Characteristics of High-Pressure Water Flowing in A Vertical Upward Smooth Tube at Low Mass Flux Conditions

The Study of Critical Heat Flux in Upflow Boiling Vertical Round Tube under High Pressure

Experimental Study on Critical Heat Flux of Two-Phase Flow in a Vertical Square Tube

Study On Heat Transfer Of High-Pressure Steam-Water Two-Phase Mixture In Helical Coils

Numerical Study on Heat Transfer and Flow Oscillations of Supercritical-Pressure Water in Helical Tubes

Hydraulic Resistance of Subcritical and Supercritical Water Flowing in A Rifled Tube

Investigation on The Characteristics of internally Riffled Tubes TwoPhase Flow Friction Pressure Losses in Subcritical and Near Critical Pressure Region

Leak Rates of High Pressure Steam–water Across Simulation Crack

Investigation of forced convection heat transfer of supercritical pressure water in a vertically upward internally ribbed tube

Experimental Investigation on Heat Transfer Characteristics of Smooth Tube with Downward Flow

Hydraulic Resistance of In-Tube Cooling Supercritical Water Accompanying Out-Tube Pool Boiling

Experimental Investigation On Heat Transfer And Frictional Characteristics Of Vertical Upward Rifled Tube In The Advanced Ultra Supercritical Steam Generator

Investigation on the Heat Transfer Characteristics of the Steam-Water Two-Phase Flow in the Inclined Upward Smooth Tube in Sub-Critical and Near Critical Pressure Regions

Experimental Investigation on Heat Transfer Characteristics of High Pressures Water in a Vertical Upward Annular Channel