Abstract:The effects of temperature on the tribological and dynamic mechanical properties (DMP) of aromatic liquid-crystal poly(ester-co-amide) were investigated. Specimens for the DMA test and friction and wear test were prepared by compression molding at elevated temperature. The dynamic mechanical properties of the resulting compression-molded liquid crystal polymer (LCP) specimens were evaluated on a Perkin-Elmer DMA instrument, in a three-point bending mode, at a heating rate of 10°C/min and frequency of 1Hz from room temperature to 250°C. The friction and wear behavior of the compression-molded LCP specimens sliding against SA52100 steel in a ball-on-disk configuration was evaluated on a high-temperature friction and wear tester from 25 to 300°C. The worn surface morphologies of the compression-molded LCP specimens were observed on a scanning electron microscope. It was found that the tribological and dynamic mechanical properties of the LCP strongly depended on the test temperature. Namely, the friction coefficients decreased significantly and the wear rate increased considerably with increasing temperature. This was attributed to the enhanced softening and plastic deformation of the LCP at elevated temperature. The LCP experienced severe plastic deformation, flowing and local melting owing to the destruction of the stiff backbones of the polymeric molecules at excessively high temperature, thus the largest wear rate of the tested LCP was generated at 300°C. Such a trend in the friction and wear behavior of the compression-molded LCP with temperature conformed well to the corresponding worn surface morphologies. Namely, the LCP worn surface was characterized by mild plastic deformation and micro-cracking as the LCP disk slid against the steel ball at 50°C, whilst at 100°C, the plastic deformation and adhesion became severe and the micro-cracking disappeared owing to the plastic flow. The plastic deformation and adhesion became increasingly more severe with further increase of the test temperature up to 150, 200, and 250°C, owing to the increased plastic flow and local softening and melting of the LCP. Moreover, the storage modulus of the compression-molded LCP greatly decreased with increasing temperature, as did the loss modulus, while the complex modulus and tan δ increased with increasing temperature, which agreed well with the corresponding trend of the tribological behavior with temperature. It was confirmed that the dynamic mechanical properties of the polymer were an important factor of the high temperature tribological behavior.

Mechanical Behavior and Constitutive Model of EPDM Inhibitor

Mechanical Behaviors of Copolymer Elastomers: Experimental Characterization and Constitutive Modelling

Constitutive Model for Thermal-Oxygen-Aged EPDM Rubber Based on the Arrhenius Law

Effect of Temperature on the Tribological and Dynamic Mechanical Properties of Liquid Crystalline Polymer

Experimental Characterization and Finite Element Modeling the Deformation Behavior of Rubbers with Geometry Defects

A rate-dependent aging constitutive model of EPDM rubber

The Effect of Thermal Aging on the Mechanical Properties of Ethylene Propylene Diene Monomer Charge Coating

Rate-Dependent Tensile Properties of Aluminum-Hydroxide-Enhanced Ethylene Propylene Diene Monomer Coatings for Solid Rocket Motors

Phenomenological Modeling of the Stress-Stretch Behavior of EPDM Rubber with Loading-rate and Damage Effects

Crack propagation velocity and fracture toughness of hydroxyl-terminated polybutadiene propellants with consideration of a thermo-viscoelastic constitutive model: Experimental and numerical study

Relationships Between Thermo-Oxidation and Dynamic Rheological Behavior of Epdm

Effects of Large Deformation and Velocity Impacts on the Mechanical Behavior of Filled Rubber: Microstructure-Based Constitutive Modeling and Mechanical Testing

Study on the performance and application of EPDM by regression analysis method

Thermal Degradation of Flame‐retarded Polyethylene/magnesium Hydroxide/poly(ethylene‐co‐propylene) Elastomer Composites

One-Dimensional Dynamic Compressive Behavior of EPDM Rubber

A volumetric ablation model of EPDM considering complex physicochemical process in porous structure of char layer

Mechanical properties and deformation behaviors of the hydroxyl-terminated polybutadiene and ammonium perchlorate interface by molecular dynamics simulation

Mechanical Properties and Thermal Behaviors of Dynamically Photocrosslinked PP/EPDM Blends

A thermally reversible healing EPDM based elastomer with higher tensile properties and damping properties

Preparation and Mechanical Properties Analysis of Rare Earth Filling Ethylene‐Allene Monomer Rubber Composite

A Study of the Novel Intumescent Flame‐retarded PP/EPDM Copolymer Blends