Abstract:Objective:Through histological analysis, immunofluorescence staining, electrophysiological detection and Sensory and motor function evaluation to investigate the effects of 3D printed hydrogel scaffold combined with bone marrow mesenchymal stem cells (BMSCs) in promoting functional recovery of spinal cord injury.Methods:10% GelMA hydrogel and 10 6 U stem cell suspension were prepared into bioink of appropriate concentration to construct the biomimetic spinal cord scaffold through 3D printing platform. The scaffold was placed in the medium and cultured in an environment of 37 ℃ CO 2 incubator. The microstructure of the scaffolds and the distribution of BMSC in the scaffolds was observed by scanning electron microscope. CAM/PI staining and confocal microscopy were used to observe the survival of stem cells in the scaffolds and determine the biocompatibility of the scaffolds. The scaffolds were implanted into the subcutaneous tissues of the back of rats, and the subcutaneous tissues were determined by HE staining to detect the immunogenicity of the scaffolds. After the rat model of hemicytoma defect was made, stents were transplanted for treatment, and confocal microscopy was used to evaluate the regeneration of neurons and axons in local area of spinal cord injury. At the same time, BBB score was used to evaluate motor function, mechanical pain score was used to evaluate sensory function, and surface electrode detection method was used to evaluate electrophysiological recovery weekly. Results:The long spindle shaped BSMC were uniformly distributed in the scaffold with a loose reticular structure. The scaffolds had good biocompatibility, and the cell survival rate of the prepared scaffolds reached 96% after 24 hours of printing. After 28 days of subcutaneous transplantation, the immune rejection was mild and immunogenicity was low. It was shown that the regenerated spinal cord tissue in the treatment group was significantly increased compared with the control group, which was widely distributed with cells after 28 days by HE staining. It was confirmed that part of the regenerated spinal cord tissue was neurons by immunohistochemical staining.Compared with the injured group, the regeneration of neurons and axons in the treatment group were significantly increased by immunofluorescence staining and confocal microscopy. In the treatment group, the BBB score recovered to 10 points, while the control group only recovered to about 1 point in the first week, which was statistically significant. And it recovered to 17 in the fourth week, while the control group only recovered to about 4 point in the four week, which was statistically significant. The Angle of inclined plate support of the treatment group was restored to 40 degrees, while it was only restored to 22 degrees in the control group. The pain threshold of the treatment group decreased to 18.5 points, which was not statistically different from that of the control group. The latent recovery effect of electrophysiology in the treatment group was the same as that in the sham operation group and better than that in the control group.Conclusion:3D printing hydrogel scaffold with loose network structure is suitable for cell proliferation. It has well biological survival, low cytotoxicity and low immunogenicity, which promoted neurons and axons to recovery and extend so as to effectively promote the recovery of motor function, sensory function and neural signal transmission rate after spinal cord injury.

3D bioprinting approaches for spinal cord injury repair

3D Bioprinted Conductive Spinal Cord Biomimetic Scaffolds for Promoting Neuronal Differentiation of Neural Stem Cells and Repairing of Spinal Cord Injury

Innovative Strategies in 3D Bioprinting for Spinal Cord Injury Repair

Development and Application of Three-Dimensional Bioprinting Scaffold in the Repair of Spinal Cord Injury

The combined application of stem cells and three-dimensional bioprinting scaffolds for the repair of spinal cord injury

3D Bioprinted Neural Tissue Constructs for Spinal Cord Injury Repair.

Biomimetic 3D-printed scaffolds for spinal cord injury repair

Application and Development of 3D Bioprinting in the Field of Spinal Cord Injury

The spatial arrangement of cells in a 3D-printed biomimetic spinal cord promotes directional differentiation and repairs the motor function after spinal cord injury

Advances in 3D printing scaffolds for peripheral nerve and spinal cord injury repair

Recent Advances in Implantable 3D-Printed Scaffolds for Repair of Spinal Cord Injury

Tissue-Engineered Regeneration of Completely Transected Spinal Cord Using Induced Neural Stem Cells and Gelatin-Electrospun Poly (Lactide-Co-Glycolide)/Polyethylene Glycol Scaffolds

Collagen/heparin Sulfate Scaffolds Fabricated by a 3D Bioprinter Improved Mechanical Properties and Neurological Function after Spinal Cord Injury in Rats.

3D printing collagen/chitosan scaffold ameliorated axon regeneration and neurological recovery after spinal cord injury

3D printed tissue engineering scaffolds combined with bone marrow mesenchymal stem cells transplantation to repair spinal cord injury

The application of 3D-bioprinted scaffolds for neuronal regeneration after traumatic spinal cord injury - A systematic review of preclinical in vivo studies

Therapeutic Effect of Biomimetic Scaffold Loaded with Human Amniotic Epithelial Cell-Derived Neural-like Cells for Spinal Cord Injury.

3D bio-printed living nerve-like fibers refine the ecological niche for long-distance spinal cord injury regeneration

Three-dimensional bioprinting sodium alginate/gelatin scaffold combined with neural stem cells and oligodendrocytes markedly promoting nerve regeneration after spinal cord injury

Bioengineered Scaffolds For Spinal Cord Repair

[application of three dimensional printing on manufacturing bionic scaffolds of spinal cord in rats].