Abstract:As additive manufacturing advances, it offers a cost-effective avenue for structurally repairing components. However, a challenge arises in the additive repair of suspended damaged surfaces, primarily due to gravitational forces. This can result in excessive deformation during the repair process, rendering the formation of proper repair impractical and leading to potential failure. In light of this rationale, conventional repair techniques are impractical for extensively damaged surfaces. Thus, this article proposes a novel repair methodology that is tailored to address large-area damage. Moreover, and departing from conventional practices involving the addition and subsequent subtraction of materials for precision machining, the proposed process endeavors to achieve more precise repair outcomes in a single operation. This paper introduces an innovative repair approach employing fused deposition modeling (FDM) to address the complexities associated with the repair of damaged polymer material parts. To mitigate geometric errors in the repaired structural components, beams with minimal deformation are printed using a compensation method. These beams then serve as supports for overlay printing. The paper outlines a methodology by which to determine the distribution of these supporting beams based on the shape of the damaged surface. A beam deformation model is established, and the printing trajectory of the compensated beam is calculated according to this model. Using the deformation model, the calculated deformation trajectories exhibit excellent fitting with the experimentally collected data, with an average difference between the two of less than 0.3 mm, validating the accuracy of the suspended beam deformation model. Based on the statistical findings, the maximum average deformation of the uncompensated sample is approximately 5.20 mm, whereas the maximum deformation of the sampled point after compensation measures around 0.15 mm. Consequently, the maximum deformation of the printed sample post-compensation is mitigated to roughly 3% of its pre-compensation magnitude. The proposed method in this paper was applied to the repair experiment of damaged curved surface components. A comparison was made between the point cloud data of the repaired surface and the ideal model of the component, with the average distance between them serving as the repair error metric. The mean distance between the point clouds of the repaired parts using the proposed repair strategy is 0.197 mm and the intact model surface is noticeably less than the mean distance corresponding to direct repair, at 0.830 mm. The repair error with compensatory support beams was found to be 76% lower than that without compensatory support beams. The surface without compensatory support beams exhibited gaps, while the surface with compensatory support beams appeared dense and complete. Experimental results demonstrate the effectiveness of the proposed method in significantly reducing the geometric errors in the repaired structural parts. The outcomes of the FDM repair method are validated through these experiments, affirming its practical efficacy. It is noteworthy that, although only PLA material was used in this study, the proposed method is general and effective for other polymer materials. This holds the potential to significantly reduce costs for the remanufacturing of widely used polymers.

A Novel 3D-Printing Repair of Surface Cracks for Improving the Mechanical Strength.

[Application of Three-Dimensional Printing Technique in Repair and Reconstruction of Maxillofacial Bone Defect].

Improving the fracture toughness of 3D printed thermoplastic polymers by fused deposition modeling

Potentials for Shade Management in Agroforestry Systems for Taro Cropping

Integrated self-monitoring and self-healing continuous carbon fiber reinforced thermoplastic structures using dual-material three-dimensional printing technology

Evaluation of Carbon Fiber-Embedded 3D Printed Structures for Strengthening and Structural-Health Monitoring

Visual Detection of Surface Defects Based on Self-Feature Comparison in Robot 3-D Printing

Fused Deposition Modeling Five-Axis Additive Manufacturing: Machine Design, Fundamental Printing Methods and Critical Process Characteristics

Novel Three-Dimensional-Printing Strategy Based on Dynamic Urea Bonds for Isotropy and Mechanical Robustness of Large-Scale Printed Products

Enhancing Additive Restoration of Damaged Polymer Curved Surfaces through Compensated Support Beam Utilization

A human monoclonal antibody obtained from EBV‐transformed B cells with specificity for myosin

Automated structural repair based on continuous carbon fiber reinforced plastic 3D printing and online model reconstruction

Crack propagation in adhesive bonded 3D printed polyamide: Surface versus bulk patterning of the adherends

Uptake on Postmilking Teat Antisepsis 1

Investigating the Integrity and Failure Characteristics of Deteriorated Polymeric 3D-Printed Components as Candidates for Structural and Construction Applications

Improved fracture resistance of 3D-printed elastoplastic structures with respect to their topology and orientation of deposited layers

Optimization Analysis of Cooling Process of 3D-Printing in FDM

Quantitative Analysis and 3D Visualization of Crack Behavior in 3D-Printed Rock-Like Specimens with Single Flaw Using In-Situ Micro-CT Imaging

A hybrid additive manufacturing platform based on fused filament fabrication and direct ink writing techniques for multi-material 3D printing

Influence Mechanism of Ultrasonic Vibration Substrate on Strengthening the Mechanical Properties of Fused Deposition Modeling

Fast Damage-Healing of Rigid Photocuring 3D Printing Materials Capable of Directly Recycling in 3D Printing