Abstract:A new type of controlled release fertilizer which enables control over both release rate and release pattern was developed. A dry mixture of soluble fertilizer and thickener is contained in a non-permeable envelope, having at least one small opening. Two main processes govern the release of nutrients from the device: (a) water penetrates through the opening(s) into the dry mixture forming a distinct and sharp wetting front. The process starts with a `burst' of water into the device; (b) nutrients leave the device through the opening either by diffusion alone or by diffusive and convective flows. Since the time pattern of the transport processes may have different forms, a simple model was used to describe the extent of wetting or release, M, as a function of time, t; M(t) = Ctα, where C and α are parameters. Several factors which affect both the water penetration and the nutrients release were investigated: fertilizer type (solubility, density), thickener type (Na-polyacrylamide and Na-carboxymethylcellulose), thickener concentration in the dry mixture, size of the device, and opening diameter. It was found that the rate of wetting and the magnitude of the `burst' effect increase with fertilizer solubility. This is reflected in the rate of nutrients release which generally increases with fertilizer solubility. Increasing thickener concentration results in a reduced rate of wetting and a smaller burst effect. In some cases, the time pattern of wetting shifts from Fickian (α ≈ 0.5) to linear (α ≈ 1.0). Consequently, the release itself is affected in a similar manner. Reducing the diameter of the opening, reduces significantly the wetting rate and even more so the release of nutrients. A decrease in the opening diameter results in a linear release pattern. The ability to control both the rate and the time pattern of the release through different combinations of the main factors is discussed and demonstrated.

The diffusion performance of fertilizer nutrient through polymer latex film.

Fabrication of Graphene Oxide/Polymer Latex Composite Film Coated on Kno3 Fertilizer to Extend Its Release Duration

Development in Polymer Latex Coated Fertilizer for Controlled Release

Release Characteristics of Nutrients from Polymer-coated Compound Controlled Release Fertilizers

Nutrient Diffusion Control of Fertilizer Granules Coated with a Gradient Hydrophobic Film

Crop Nitrogen Uptake and Its Requirement on Film Coated Controlled-Release Fertilizer

Crosslinking using particulate crosslinker in polymer latex film-coating process for controlled-release fertilizer

Nutrient controlled release performance of bio-based coated fertilizer enhanced by synergistic effects of liquefied starch and siloxane

Release characteristics of a new controlled release fertilizer

Research on the Effects of Macromolecule Compound Materials on Release Characteristics of Different Forms of Nitrogen Nutrients

A biodegradable multifunctional pectin-montmorillonite fertilizer coating: Controlled-release, water-retention and soil-cementation

Polymer coated slow/ controlled release granular fertilizers: Fundamentals and research trends

Enhancing Film Cross-Linking Through VTES Copolymerization in Polymer Latex for Increasing Controlled-Release Performance of Film-Coated Fertilizer Granules

The Influence of the Velocity of Release of Nutrient with the Coating Urea and in Different Soil

Polymethyl methacrylate-g-carboxy-methylcellulose as an amphiphilic coating material for slow-release fertilizer

Engineering and slow‐release properties of lignin‐based double‐layer coated fertilizer

Controlled-release fertilizer encapsulated by starch/polyvinyl alcohol coating

Experimental Modeling of Polymer Latex Spray Coating for Producing Controlled-Release Urea

Slow-Release Urea Fertilizer with Water Retention and Photosensitivity Properties Based on Sodium Alginate/Carboxymethyl Starch Sodium/Polydopamine

Structural control of PEG-intercalating Na-bentonite and its influence on the properties of castor oil-based polyurethane coating

Biobased Polyurethane, Epoxy Resin, and Polyolefin Wax Composite Coating for Controlled-Release Fertilizer