Abstract:In this dissertation, the relationships between structure-mechanical properties-deformation mechanisms in face-centered cubic (FCC) and body-centered cubic (BCC) metallic nanowires have been studied using in situ TEM nanomechanical testing. It is well known that smaller is stronger and the widely-observed size effect is believed to arise from dislocation interactions inside nanocrystals. However, the interaction mechanisms in small-volume nanocrystals remain unexplored. Here, it was found that surface-nucleated dislocations can strongly interact inside the confined volume of Au nanowires, which led to a new type of dislocation-originated stacking fault tetrahedra (SFT), at variance to the widely-believed vacancy-originated SFT. The atomic-scale processes of nucleation, migration and annihilation of dislocation-originated SFT were revealed, shedding new light onto the strain hardening and size effect in small-volume materials. Although nanoscale twinning is an effective mean to enhance the strength of metals, twin-size effect on the deformation and failure of nanotwinned metals remains largely unexplored, especially at the minimum twin size. Here, a new type of size effect in nanotwinned Au nanowires is presented. As twin size reaches the angstrom-scale, Au nanowires exhibit a remarkable ductile-to-brittle transition that is governed by the heterogeneous-to-homogeneous dislocation nucleation transition. Quantitative measurements show that approaching such a nanotwin size limit gives rise to the ultra-high strength in Au nanowires, close to the ideal strength limit of perfect Au. Twinning is a fundamental deformation mode that competes against dislocation slip in crystals. At the nanoscale, higher stresses are required for plastic deformation than that in bulk, which favors twinning over dislocation slip. Indeed, deformation twinning has been well-documented in FCC nanocrystals. However, it remains unexplored in BCC nanostructures. Here, it shows that twinning is the dominant deformation mode in BCC-tungsten nanocrystals. A competition between twinning and dislocation slip occurs when changing the loading orientations, attributed to the defect growth controlled plasticity in BCC nanocrystals. Several important commonalities and differences in FCC and BCC nanocrystals deforming at nanoscale are further proposed. The results from this dissertation advance fundamental understanding of plastic deformation in a broad class of metals and alloys, and are of technological importance for degradation control and future design of ultra-strength nanomaterials.

Dislocation Multiplications in Extremely Small Hexagonal-structured Titanium Nanopillars Without Dislocation Starvation

In Situ TEM Study on the Nanomechanical Behaviors of Metallic Nanowires

Discrete Twinning Dynamics and Size-Dependent Dislocation-to Twin Transition in Body-Centred Cubic Tungsten

Interactions Between Dislocations and Penta-Twins in Metallic Nanocrystals

Size-Dependent Dislocation-Twin Interactions

High-Strength Titanium Alloy Nanopillars with Stacking Faults and Enhanced Plastic Flow

In Situ TEM Investigation of the Mechanical Behavior of Micronanoscaled Metal Pillars

Surface-controlled dislocation multiplication in metal micropillars

High-order Hierarchical Nanotwins with Superior Strength and Ductility

The Effect of Size on the Deformation Twinning Behavior in Hexagonal Close-Packed Ti and Mg

New Mechanisms of Helical Dislocation Formation Via the Pinch-off Process Near a Nano-Inhomogeneity

Size effects and plastic deformation mechanisms in single-crystalline CoCrFeNi micro/nanopillars

SIZE EFFECT ON DEFORMATION MODE IN MICRON-SIZED Ti-5Al SINGLE CRYSTAL LOADED ALONG $[2\,\overline 1 \,\overline 1 \,0]$ AND [0001]

Dislocation-mediated ultrahigh mechanical properties in nano-TiN

Unraveling size-affected plastic heterogeneity and asymmetry during micro-scaled deformation of CP-Ti by non-local crystal plasticity modeling

Atomistic Modelling of All Dislocations and Twins in HCP and BCC Ti

Intrinsic Size Dependent Plasticity in BCC Micro-Pillars under Uniaxial Tension and Pure Torsion

Dislocation Evolution in Cyclic‐Loaded Cu Nanopillars with Different Configurations

Enhanced strength in pure Ti via design of alternating coarse- and fine-grain layers

Analysis of the Twin Spacing and Grain Size Effects on Mechanical Properties in Hierarchically Nanotwinned Face-Centered Cubic Metals Based on A Mechanism-Based Plasticity Model

Anisotropic Mechanical Properties and Deformation Mechanisms of Nanotwinned Ni and Ni Alloys With Extremely Fine Twin Boundary Spacings