Abstract:The MAX phase has attracted much attention due to its unique properties combined with the merits of both metal and ceramic, including the low density, high electrical conductivity and good oxidation resistance, which makes it significant for possible applications in various high temperature or other environments. There is a lot of research work on Ti2AlX (X=C, N). However little research about thermodynamic properties at high pressure is carried out. So we study the structural, mechanical and thermodynamic properties of Ti2AlC and Ti2AlN at various pressures and temperatures. The first-principles calculations based on electronic density-functional theory framework are used to investigate the properties at various pressures. The cut-off energy is 350 eV. Converged results are achieved with 10102 special K-point meshes. The self-consistent convergence of total energy is set to be 5.010-6 eV/atom. According to the calculated structural parameters at various pressures, we can find that the ratios V/V0 (V0 denotes the system volume at 0 GPa) of Ti2AlX are reduced by 20.59% and 18.93%, respectively, so the compressibility of the system is strong. As the internal pressure increases, the curves of V/V0 become gentle. Then we calculate elastic constants at pressures ranging from 0 to 50 GPa in steps of 10 GPa. It is obvious that the Ti2AlX is mechanically stable because all of the elastic constants satisfy the Born stability criteria. The bulk modulus, shear modulus and Young's modulus linearly increase with internal pressure increasing, implying that the pressure can improve the resistance to volume deformation. The ductility and brittleness can be judged according to Pugh's criterion (ratio of bulk modulus to shear modulus B/G), and the brittle nature turns into ductile nature in a pressure range of 40-50 GPa for the Ti2AlX since the value of B/G exceeds 1.75. Finally, we study the thermodynamic properties at various pressures and temperatures based on the quasi-harmonic Debye approximation theory, including the bulk modulus, heat capacity and thermal expansion coefficient. The bulk modulus decreases with temperature increasing but increases with pressure increasing. The heat capacity at constant volume Cv and the heat capacity at constant pressure Cp have the same variation tendency, while Cv obeys the Dulong-Petit limit. It is easy to see that temperature and pressure have opposite influences on heat capacity and the effect of temperature is more significant than that of pressure. The effects of temperature and pressure on linear expansion coefficient mainly occur at low temperature and the effect of pressure is not so considerable when the pressure exceeds 30 GPa. Above all, the effects of temperature and pressure on thermodynamic properties are inverse.

Effects of pressure on structural, mechanical, dynamics and thermal properties of Rankinite: Insights from first-principles calculations

First-principles Investigations of Elastic Stability and Electronic Structure of Cubic Platinum Carbide under Pressure

First-Principles Study of Electronic and Elastic Properties of Hexagonal Layered Crystal MoS2 Under Pressure

First-Principles Calculations for Elastic Properties of ZnS under Pressure

The first-principles calculations for the elastic properties of Zr2Al under compression

Elastic Constants and Anisotropy of RuB2under Pressure

A Molecular Dynamics Study of the Mechanical Properties of Kaolinite under Uniaxial and Isothermal Compression at Various Temperatures

Anisotropy in Elasticity and Physical Properties of Ti2B under High Pressure

Abnormal Elastic Changes for Cubic-Tetragonal Transition of Single-Crystal SrTiO3

First-Principles Investigations of Structural, Elastic, Mechanical Properties of ZnCr2S4 under Pressure

First-principles Study on the Structural Stabilities, Electronic and Elastic Properties of Zr2Si Alloy under Pressure

Influence of high pressure on mechanical and electronic properties of C3060 allotropes—A first-principles investigation

Elastic Stability of CO_{2} Phase I under High Temperature and Pressure

First-principles calculations of high-pressure physical properties anisotropy for magnesite

Structural, Mechanical, and Thermodynamic Properties of Ti2AlX (X = C, N) at High Pressure

First-principles study on the structural stabilities, electronic and elastic properties for zirconium under pressure

High Pressure Effects on the Crystal Structure and Electric Conductivity of Perovskite Like (ca/sr) 2 CuO 2 Cl 2 Compounds

Theoretical prediction of structural, elastic and thermodynamic properties of transition metal monosilicides CrSi, TiSi and ZrSi under high pressure

Structural, mechanical, thermodynamic and electronic properties of Pt3M (M = Al, Co, Hf, Sc, Y, Zr) compounds under high pressure

Pressure Effect on Elastic Constants and Related Properties of Ti3Al Intermetallic Compound: A First-Principles Study

Structural, mechanical properties, and vibrational spectra of LLM-105 under high pressures from a first-principles study