Abstract:The MAX phase has attracted much attention due to its unique properties combined with the merits of both metal and ceramic, including the low density, high electrical conductivity and good oxidation resistance, which makes it significant for possible applications in various high temperature or other environments. There is a lot of research work on Ti2AlX (X=C, N). However little research about thermodynamic properties at high pressure is carried out. So we study the structural, mechanical and thermodynamic properties of Ti2AlC and Ti2AlN at various pressures and temperatures. The first-principles calculations based on electronic density-functional theory framework are used to investigate the properties at various pressures. The cut-off energy is 350 eV. Converged results are achieved with 10102 special K-point meshes. The self-consistent convergence of total energy is set to be 5.010-6 eV/atom. According to the calculated structural parameters at various pressures, we can find that the ratios V/V0 (V0 denotes the system volume at 0 GPa) of Ti2AlX are reduced by 20.59% and 18.93%, respectively, so the compressibility of the system is strong. As the internal pressure increases, the curves of V/V0 become gentle. Then we calculate elastic constants at pressures ranging from 0 to 50 GPa in steps of 10 GPa. It is obvious that the Ti2AlX is mechanically stable because all of the elastic constants satisfy the Born stability criteria. The bulk modulus, shear modulus and Young's modulus linearly increase with internal pressure increasing, implying that the pressure can improve the resistance to volume deformation. The ductility and brittleness can be judged according to Pugh's criterion (ratio of bulk modulus to shear modulus B/G), and the brittle nature turns into ductile nature in a pressure range of 40-50 GPa for the Ti2AlX since the value of B/G exceeds 1.75. Finally, we study the thermodynamic properties at various pressures and temperatures based on the quasi-harmonic Debye approximation theory, including the bulk modulus, heat capacity and thermal expansion coefficient. The bulk modulus decreases with temperature increasing but increases with pressure increasing. The heat capacity at constant volume Cv and the heat capacity at constant pressure Cp have the same variation tendency, while Cv obeys the Dulong-Petit limit. It is easy to see that temperature and pressure have opposite influences on heat capacity and the effect of temperature is more significant than that of pressure. The effects of temperature and pressure on linear expansion coefficient mainly occur at low temperature and the effect of pressure is not so considerable when the pressure exceeds 30 GPa. Above all, the effects of temperature and pressure on thermodynamic properties are inverse.

Structural, mechanical, thermodynamic and electronic properties of Pt3M (M = Al, Co, Hf, Sc, Y, Zr) compounds under high pressure

First-principles Investigations of Elastic Stability and Electronic Structure of Cubic Platinum Carbide under Pressure

Theoretical study of the elastic and thermodynamic properties of Pt$_{3}$Al with the L1$_{2}$ structure under high pressure

Structural, Mechanical, and Thermodynamic Properties of Ti2AlX (X = C, N) at High Pressure

Ab initio study of AlCu2M (M = Sc, Ti and Cr) ternary compounds under pressures

First-principles Investigations on Structural, Elastic, Thermodynamic and Electronic Properties of Ni3X (X = Al, Ga and Ge) under Pressure

First-principles Study of Electronic Structural and Mechanical Properties of MgxLa(x=1, 2, 3) Compounds under Pressure

Anisotropy in Elasticity and Physical Properties of Ti2B under High Pressure

The Mechanical and Thermodynamic Properties of Heusler Compounds Ni2xal (X = Sc, Ti, V) under Pressure and Temperature: A First-Principles Study

The Structural, Mechanical and Thermodynamic Properties of Ti-B Compounds under the Influence of Temperature and Pressure: First-principles Study

First-principle Studies on the Mechanical, Thermodynamic and Electronic Properties of Β″-Mg3gd and Β′-Mg7gd Alloys under Pressure

First-principles Study of Mechanical Properties and Electronic Structures of the Nickel-molybdenum Binary Compounds Under Pressure

Structural, Elastic, Electronic and Optical Properties of Platinum-Based Superconductor Srpt3p under Pressure: A First-Principles Study

Pressure Prediction of Electronic, Anisotropic Elastic, Optical, and Thermal Properties of Quaternary (m2/3ti1/3)(3)alc2 (M = Cr, Mo, and Ti)

Pressure-induced effects on the mechanical and thermophysical properties of LiAl2X (X = Rh, Pd, Ir and Pt) ternary intermetallic compounds

First Principles Calculations on Elastic, Thermodynamic and Electronic Properties of Co2Zr and Co2Ti at High Temperature and Pressure

Pressure Effect on Elastic Constants and Related Properties of Ti3Al Intermetallic Compound: A First-Principles Study

Pressure Prediction of Electronic, Anisotropic Elastic, Optical, and Thermal Properties of Quaternary (M<sub>2/3</sub>Ti<sub>1/3</sub>)<sub>3</sub>AlC<sub>2</sub>(M = Cr, Mo, and Ti)

Theoretical prediction of structural, elastic and thermodynamic properties of transition metal monosilicides CrSi, TiSi and ZrSi under high pressure

Pressure Effects on Elastic and Thermodynamic Properties of Zr3al Intermetallic Compound

First-principles study of mechanical and electronic properties of TiB compound under pressure