Abstract:For high-power UV laser facilities, one of the key problems limiting the maximum light influence and safe routine operation is that the UV laser induces damage to fused silica optics. The most effective mitigation protocol of the damaged optics is the CO2 laser processing that leads to make locally melt or evaporate the damage. While the mitigated damage sites possess particular morphology, which may modulate the passing laser beam and induce the downstream intensification that will ruin the neighbor optics. In this work, the morphology features of the mitigated damage pits of fused silica optics are systematically investigated. According to the measured morphology features, a 3D grid model of mitigated pit is built, and the downstream light intensity distribution of the mitigated pit model under incident 351 nm laser is studied by scalar diffraction theory and fast fourier transform (FFT) methods. Results indicate that there are two kinds of downstream intensification: off-axis and on-axis intensifications. In the former intensification, the maximum intensity is located near the output surface of the optics and comes mainly from the depth of the mitigated pit; it increases with the depth. In the alter intensification, the maximum intensity is located far from the output surface of the optics and is mainly dependent on the height of the rim structure at the fringe of the mitigated damage pit; so it increase with increasing height. In addition, it is found that the location of the maximum off-axis or on-axis intensity can approach the output surface of the optics with increasing maximum intensity. For comparison, experimental measurements of downstream intensification induced by the mitigated pits are carried out, and the experimental results are almost consistent with the numerical simulation, implying the validity of the numerical simulation of the mitigated pit model. Results of this research indicate that the downstream intensification of mitigated pits can be suppressed by controlling the morphology features of mitigated pits. this is significant for the development and improvement of the mitigated techniques of damage optics.

Optimization of morphological parameters for mitigation pits on rear KDP surface: experiments and numerical modeling.

Secondary Peak of Downstream Light Field Modulation Caused by Gaussian Mitigation Pits on the Rear KDP Surface

Downstream Light Intensification Induced by Gaussian Mitigation Pits Using Micro-Milling on Rear KDP Surface

Development of Optimal Mitigation Contours and Their Machining Flow by Micro-Milling to Improve the Laser Damage Resistance of KDP Crystal

Modeling of Residual Tool Mark Formation and Its Influence on the Optical Performance of KH2PO4 Optics Repaired by Micro-Milling

Fabrication of Spherical Mitigation Pit on Kh2po4 Crystal by Micro-Milling and Modeling of Its Induced Light Intensification

Application of light diffraction theory to qualify the downstream light field modulation property of mitigated KDP crystals

Potential Damage Threats to Downstream Optics Caused by Gaussian Mitigation Pits on Rear KDP Surface

Study of Downstream Light Intensity Modulation Induced by Mitigated Damage Pits of Fused Silica Using Numerical Simulation and Experimental Measurements

Effect of Structural Parameters of Gaussian Repaired Pit on Light Intensity Distribution Inside KH 2 PO 4 Crystal

Role of Tool Marks Inside Spherical Mitigation Pit Fabricated by Micro-Milling on Repairing Quality of Damaged KH2PO4 Crystal

Laser damage evolution by defects on diamond fly-cutting KDP surfaces

Effect of Pre-Existing Micro-Defects on Cutting Force and Machined Surface Quality Involved in the Ball-End Milling Repairing of Flawed KDP Crystal Surfaces.

Repaired Morphology of CO 2 Laser Rapid Ablation Mitigation of Fused Silica and Its Influence on Downstream Light Modulation

Dynamic behavior modeling of laser-induced damage initiated by surface defects on KDP crystals under nanosecond laser irradiation

Investigation on Machining Performance of Soft-Brittle KDP Crystals with Surface Micro-Defects in the Ball-End Milling Repairing Process

Optical Modulation of Repaired Damage Site on Fused Silica Produced by CO2 Laser Rapid Ablation Mitigation

Morphology evolution mechanisms and localized structural modification of repaired sites on fused silica optics processed by CO2 laser rapid ablation mitigation

Combined Modulation of Incident Laser Light by Multiple Surface Scratches and Their Effects on the Laser Damage Properties of KH2PO4 Crystal.

Research on Light Intensity Modulation Within KDP Crystal Based on Different Width of Gaussian Repaired Contour of Surface Defects

Initial energy deposition and initiation mechanism of nanosecond laser damage caused by KDP surface micro-defects