Abstract:The impact of minor Mg addition on microstructure and mechanical properties of cast Al–Li–Cu–Zr alloy with high lithium content (3 wt % Li) were studied to understand a qualitative assessment of sequence and kinetics of multiple precipitations and its effect on mechanical properties. Scanning Electron Microscope and X-ray diffraction results suggested that raising the content of Mg gradually altered the grain structure of the as-cast alloys and increased the types and volume fraction of the grain boundary intermetallic phase. Unusually, solvus temperature is higher than solidus temperature in 0.5 Mg alloy (Al–3Li–2Cu-0.5Mg-0.15Zr, wt. %), resulting in the incipient melting of the matrix before the complete dissolution of the intermetallic phases. Prominent enhancements in both age-hardening and precipitation kinetics of the base alloy with the addition of Mg were also easily identified, indicating the important role of Mg during isothermal aging. Transmission Electron Microscope and atom probe tomography results showed that minor Mg addition (0.2 wt %, denoted by 0.2 Mg alloy) could encourage the diffusion of Cu atoms by the aggregation of Mg–Cu-vacancy co-clusters, thereby promoting the nucleation of the T1-Al2CuLi and θ′-Al2Cu precipitates. In addition, S′-Al2CuMg precipitate was therefore introduced as a result of Mg addition. With further increasing the content of Mg to 0.5 wt %, the nucleation and growth of S′ precipitate would be promoted at the expense of T1 and θ′ precipitates, especially the latter. Based on the theoretical models and regression analysis, the formation mechanism of δ′-Al3Li precipitate-free-zones gradually changed from the initial vacancy-depletion mechanism to the solute-depletion mechanism, and Mg element could significantly inhibit the coarsening of δ′ precipitate-free-zones. The best balance between ductility and strength was obtained by 0.2 Mg alloy aged for 32 h, and the alloys have significant advantages in terms of density (2.437 g/cm3) and elastic modulus (82.65 GPa) over conventional cast aluminum alloys (density: 2.7–2.8 g/cm3; elastic modulus: 72 GPa).

Influence of Li2sb Additions on Microstructure and Mechanical Properties of Al-20mg(2)Si Alloy

The Effect of Solution Treatment on the Si Particles’ Morphology Evolution and the Thermal Conductivity and Tensile Properties of Sb-Modified Al-8Si-0.6Mg Alloys

Regulative Effect of Mg/Si Ratio on Microstructure Evolution and Mechanical Properties of Cast Al-Li-Mg-Si Alloys

Effects of Si Content and Modification on Microstructure and Properties of In-situ Mg2Si/Mg Composites

Effect of Li Content on Microstructure and Mechanical Property of Mg−xLi−3(Al−Si) Alloys

The Effect of Si Content on the Microstructure and Mechanical Properties of Al–1.2Mg–xSi–1.2Cu–0.6Mn Cast Alloy

Influences of Mg content on the microstructures and mechanical properties of cast Al–2Li–2Cu–0.2Zr alloy

Cooperative Effect of Mg and Si Contents on the Microstructural Evolution, Mechanical Performance, and Deformation Behavior of Cast Al–Li–Mg–Si Alloys

Influence of the Mg Content on the Microstructure and Mechanical Properties of Al-xMg-2.0Si-0.6Mn Alloy

Effect of Li addition on microstructure and mechanical properties of Al – Mg – Si alloy

Mechanical Properties Improvement of Mg-Al Based Alloy with Sb Addition

The synergistic effect of Li addition on microstructure, texture and mechanical properties of extruded Al–Mg–Si alloys

Modification of Primary Mg2si in Mg-4si Alloys with Antimony

Effects of Sb on Microstructure and Mechanical Properties of Mg-5.5al-1.2y Alloy

Influence of Sb on damping capacity and mechanical properties of Mg2Si/Mg–9Al composite materials

Influence of Al-Si eutectic alloy on the mechanical behaviors and microstructure feature of ultralight dual-phase Mg-8Li-x(Al-12.6 Si) alloys

Significant roles of minor Mg addition in microstructural evolution and mechanical properties of cast Al–3Li–2Cu-0.15Zr alloy

Effects of Al Concentration on Microstructure and Mechanical Properties of Mg-xAl-1Zn-1Si Alloy

Sn-Sc microalloying-induced property improvement and micromechanisms of an Al-Mg-Si alloy

Microstructure and Mechanical Properties of Cast Al-Li-Mg Alloy: Role of Cu Addition and Heat Treatment

Effect of Mg Addition on the Microstructure and Mechanical Properties of SiC Nanowires Reinforced 6061al Matrix Composite