Abstract:Third-generation biosensors use enzymes capable of direct electron transfer (DET) to the sensor surface. They are of interest for continuous glucose monitoring in blood or interstitial fluid, but they are rarely investigated. One reason is the hindered DET of the enzymes to the metallic electrodes. In this publication, a novel method for the immobilization of cellobiose dehydrogenase (CDH) DET enzymes employing conductive poly(3,4-ethylenedioxythiophene)-poly (styrene sulfonate) (PEDOT:PSS) inks and a protective polyethylene glycol dimethacrylate (PEG-DMA) hydrogel layer on gold electrodes is reported. This layer stack showed a glucose-specific current response for voltages between −0.2 and 0.4 V in physiological PBS buffer, and enabled interference-less sensing in a solution of acetaminophen, ascorbic acid, dopamine, and uric acid at 0 V. A Michaelis–Menten fit led to a maximum current density (Imax) of 257 ± 7.9 nA/mm2 and a Michaelis–Menten constant (Km) of 28.4 ± 2.2 mM, with a dynamic range of 0.1–20 mM glucose and a limit of detection of 0.1 mM. After 16 h of continuous measurement of 20 mM glucose, the signal decreased to 60% of its initial value. Storage stability was successfully verified until up to 10 days. In summary, this paper shows a simplified approach for the fabrication of third-generation biosensors using CDH-PEDOT:PSS and PEG-DMA hydrogel inks.

What problem does this paper attempt to address?

The main problem that this paper attempts to solve is to develop a new type of third - generation glucose biosensor. This sensor uses the direct electron transfer (DET) enzyme - cellobiose dehydrogenase (CDH), and immobilizes CDH on a planar gold electrode through the conductive polymer poly(3,4 - ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) ink and the polyethylene glycol dimethacrylate (PEG - DMA) hydrogel layer, in order to achieve highly sensitive, selective and stable detection of glucose. Specifically, the paper aims to: 1. **Improve the enzyme immobilization effect**: By using the PEDOT:PSS conductive polymer and the PEG - DMA hydrogel layer, enhance the immobilization effect of CDH on the electrode surface, prevent the enzyme from being washed off during use, and thus improve the stability and reusability of the sensor. 2. **Optimize sensor performance**: Study the influence of different conditions (such as CDH concentration, applied potential, etc.) on sensor performance to optimize the response speed, sensitivity and dynamic range of the sensor. 3. **Reduce interference signals**: By selecting an appropriate potential range (such as 0 V), reduce the interference of other reducing substances (such as acetaminophen, ascorbic acid, dopamine and uric acid) on the sensor signal, and improve the selectivity of the sensor. 4. **Verify long - term stability and operational stability**: Evaluate the performance of the sensor under continuous measurement and storage conditions to ensure its reliability and stability in practical applications. Through systematic experimental research, the paper shows the specific current response of this new - type sensor to glucose in physiological buffer, and can still maintain high selectivity in the presence of interfering substances. In addition, the sensor shows good stability and operational stability under continuous measurement and storage conditions, providing new ideas and technical support for the development of third - generation biosensors for continuous blood - glucose monitoring.

Novel Approach for the Immobilization of Cellobiose Dehydrogenase in PEDOT:PSS Conductive Layer on Planar Gold Electrodes

Research on Direct Electron Transfer of Native Glucose Oxidase at PEDOT:PSS Hydrogels Modified Electrode

Microbial surface display of glucose dehydrogenase for amperometric glucose biosensor

A Novel Glucose Sensor System with Au Nanoparticles Based on Microdialysis and Coenzymes for Continuous Glucose Monitoring

A Glucose Biosensor Based on Direct Electron Transfer of Glucose Oxidase on PEDOT Modified Microelectrode

Construction of flexible enzymatic electrode based on gradient hollow fiber membrane and multi-wall carbon tubes meshes.

Direct Electrochemical Detection of Glucose on PEDOT Functionalized Screen-Printed Electrodes

An Enzyme-Metal-Insulator-Silicon Structured Sensor Using Surface Photovoltage Technology for Potentiometric Glucose Detection

Flexible Enzymatic Glucose Electrochemical Sensor Based on Polystyrene-Gold Electrodes

Electrochemical Sensor Array for Glucose Monitoring Fabricated by Rapid Immobilization of Active Glucose Oxidase within Photochemically Polymerized Hydrogels

A Conductive Hydrogel Microneedle-Based Assay Integrating PEDOT:PSS and Ag-Pt Nanoparticles for Real-Time, Enzyme-Less, and Electrochemical Sensing of Glucose

Efficient Immobilization of Glucose Oxidase on Nanocomposite via Layer-by-Layer Self-Assembly to Construct Bionanomultilayer Films

Self-assembled perylene-tetracarboxylic acid/multi-walled carbon nanotube adducts based modification of screen-printed interface for efficient enzyme immobilization towards glucose biosensing

Multilayer Membranes Via Layer-By-Layer Deposition Of Organic Polymer Protected Prussian Blue Nanoparticles And Glucose Oxidase For Glucose Biosensing

ELECTROCHEMICAL-BEHAVIOR, APPLICATION AND IMMOBILIZATION OF GLUCOSE-OXIDASE AT NANOMETER-SIZED ULTRAMICROBAND GOLD ELECTRODE

Single‐Component Electroactive Polymer Architectures for Non‐Enzymatic Glucose Sensing

Palladium hexacyanoferrate hydrogel as a novel and simple enzyme immobilization matrix for amperometric biosensors

Covalent Immobilisation of a Nanoporous Platinum Film onto a Gold Screen-Printed Electrode for Highly Stable and Selective Non-Enzymatic Glucose Sensing

Preparation of the Glucose Sensor Based on Three-Dimensional Ordered Macroporous Gold Film and Room Temperature Ionic Liquid

One-Step Immobilization Of Glucose Oxidase In A Silica Matrix On A Pt Electrode By An Electrochemically Induced Sol-Gel Process