Improving the Power Generation of Microbial Fuel Cells by Modifying the Anode with Single-Wall Carbon Nanohorns.

Jiawei Yang,Shaoan Cheng,Yi Sun,Chaochao Li

DOI: https://doi.org/10.1007/s10529-017-2384-4

2017-01-01

Biotechnology Letters

Abstract:To increase the power generation of microbial fuel cells (MFCs), anode modification with carbon materials (activated carbon, carbon nanotubes, and carbon nanohorns) was investigated.

What problem does this paper attempt to address?

High‐Performance Carbon Anode Derived from Sugarcane for Packed Microbial Fuel Cells

Yuhong Zhou,Guowang Zhou,Lu Yin,Jinyi Guo,Xiankai Wan,Huixiang Shi

DOI: https://doi.org/10.1002/celc.201600510

IF: 4

2017-01-01

ChemElectroChem

Abstract:Microbial fuel cells (MFCs) provide a new opportunity to produce sustainable energy from the treatment of the organic matter in wastewater. However, the power density of MFCs for large-scale application is limited by the performance of anode, with one of the major factors being low bacterial adhesion capacity. In this work, a novel macroporous sugarcane carbon (SC) is prepared by a direct carbonization process, and is used as anode material in a packed MFC. A maximum power density of 59.94 +/- 2.81Wm(-3) is achieved in an MFC equipped with the SC anode, which is 2.62times higher than that of the granular activated carbon (GAC) anode. A microbial analysis shows that the SC anode has a higher amount of biomass and the abundance of Geobacter is 6.6times higher than that of the GAC anode, which indicates that the SC anode has higher biocompatibility. Further studies show that the macroporous structure, high surface roughness, large surface hydrophobicity and low absolute value of zeta potential favor bacterial adhesion to the SC anode surface. Therefore, this study provides an excellent anode material for high-performance MFCs, and reveals the impact of physicochemical properties on power generation.
Nano-Fe3O4 Coated on Carbon Monolith for Anode Enhancement in Microbial Fuel Cells

Yini Chen,Fan Zhao,Yu Pu,Xiangyu Lin,Haoran Yin,Xinhua Tang

DOI: https://doi.org/10.1016/j.jece.2023.109608

IF: 7.7

2023-01-01

Journal of Environmental Chemical Engineering

Abstract:Anode materials were vital for power production in microbial fuel cells (MFCs). By freeze-drying and carbonization, porous carbon monolith derived from wax gourd (WGCM) was prepared. WGCM was then coated by nano-Fe3O4 to obtain the nano-Fe3O4/WGCM anode. WGCM anode increased the maximum power density of the MFCs from 430.6 mW/m2 to 906.6 mW/m2, while nano-Fe3O4/WGCM anode further promoted it to 1438.8 mW/m2. WGCM had a three-dimensional (3D) microporous network structure, a hydrophilic surface and good conductivity, which enhanced biofilm formation and reduced internal resistance. Fe3O4 increased Geobacter enrichment on anode surface, a popular electricigen in MFCs. Calculated from anode surface microbial cell density and the relative abundance, Geobacter on the nano-Fe3O4/WGCM increased by 41.4% compared with the WGCM anode. The results demonstrated that the preparation of carbon monolith coated with nano-Fe3O4 was a promising method for anode enhancement in MFCs.
Functional Nanomaterial-Modified Anodes in Microbial Fuel Cells: Advances and Perspectives

Yu-Jing Jiang,Su Hui,Li-Ping Jiang,Jun-Jie Zhu

DOI: https://doi.org/10.1002/chem.202202002

2023-01-01

Chemistry - A European Journal

Abstract:Microbial fuel cell (MFC) is a promising approach that could utilize microorganisms to oxidize biodegradable pollutants in wastewater and generate electrical power simultaneously. Introducing advanced anode nanomaterials is generally considered as an effective way to enhance MFC performance by increasing bacterial adhesion and facilitating extracellular electron transfer (EET). This review focuses on the key advances of recent anode modification materials, as well as the current understanding of the microbial EET process occurring at the bacteria-electrode interface. Based on the difference in combination mode of the exoelectrogens and nanomaterials, anode surface modification, hybrid biofilm construction and single-bacterial surface modification strategies are elucidated exhaustively. The inherent mechanisms may help to break through the performance output bottleneck of MFCs by rational design of EET-related nanomaterials, and lead to the widespread application of microbial electrochemical systems.
High-Power Microbial Fuel Cells Based on a Carbon-Carbon Composite Air Cathode.

Xiaoyuan Zhang,Qiuying Wang,Cheng Tang,Hao-Fan Wang,Peng Liang,Xia Huang,Qiang Zhang

DOI: https://doi.org/10.1002/smll.201905240

IF: 13.3

2020-01-01

Small

Abstract:Microbial fuel cells (MFCs) can convert organics in wastewater directly to electricity, and improving oxygen reduction reaction (ORR) performance is critical to their development and future applications. Electrocatalytic ORR performance is determined by the intrinsic activity and accessible amounts of active sites. A surface nitrogen-enriched carbon coaxial nanocable (NCCN) is applied as an ORR electrocatalyst and combined with activated carbon (AC) with 80 wt% addition as a carbon-carbon composite air cathode in MFCs. The fully exposed nitrogen active sites of NCCN contribute to the enhanced ORR activity, while the graphitized core affords a rapid pathway for electron transportation. AC serves as a spacer to construct a porous framework with interconnected ion diffusion channels. This cathode thus exhibits a maximum power density of 2090 mW m(-2), 120% higher than commercial Pt/C electrocatalysts, and also 6% higher than the pure NCCN, indicating a synergistic effect between NCCN and AC. A high-performance NCCN-AC air cathode with a great promise for future MFC applications is reported and an effective strategy to bridge the electrocatalytic performance from nanomaterials to practical devices is presented.
Anode Modification with Formic Acid: A Simple and Effective Method to Improve the Power Generation of Microbial Fuel Cells

Weifeng Liu,Shaoan Cheng,Jian Guo

DOI: https://doi.org/10.1016/j.apsusc.2014.09.088

IF: 6.7

2014-01-01

Applied Surface Science

Abstract:The physicochemical properties of anode material directly affect the anodic biofilm formation and electron transfer, thus are critical for the power generation of microbial fuel cells (MFCs). In this work, carbon cloth anode was modified with formic acid to enhance the power production of MFCs. Formic acid modification of anode increased the maximum power density of a single-chamber air-cathode MFC by 38.1% (from 611.5 +/- 6 mW/m(2) to 877.9 +/- 5 mW/m(2)). The modification generated a cleaner electrode surface and a reduced content of oxygen and nitrogen groups on the anode. The surface changes facilitated bacterial growth on the anode and resulted in an optimized microbial community. Thus, the electron transfer rate on the modified anodes was enhanced remarkably, contributing to a higher power output of MFCs. Anode modification with formic acid could be an effective and simple method for improving the power generation of MFCs. The modification method holds a huge potential for large scale applications and is valuable for the scale-up and commercialization of microbial fuel cells. (C) 2014 Elsevier B.V. All rights reserved.
Increasing Power Generation of Microbial Fuel Cells with a Nano-Ceo2modified Anode

Yao Yin,Guangtuan Huang,Ningbo Zhou,Yongdi Liu,Lehua Zhang

DOI: https://doi.org/10.1080/15567036.2014.898112

2016-01-01

Abstract:Nano-CeO2 was used to modify the carbon felt anode in microbial fuel cell (MFC). The MFC with the modified anode obtained the higher closed circuit voltage resulting from the lower anode potential, the higher maximum power density (2.94 W m(-2)), and the lower internal resistance (77.1 Omega). Cyclic voltammetry (CV) results implied that the bioelectrochemical activity of exoelectrogens was promoted by nano-CeO2. Electrochemical impedance spectroscopy (EIS) results revealed that the anodic charge transfer resistance of the MFC decreased with modified anode. This study demonstrates that the nano-CeO2 can be an effective anodic catalyst for enhancing the power generation of MFC.
Enhanced Electricity Generation for Microbial Fuel Cell by Using Electrochemical Oxidation to Modify Carbon Cloth Anode

Jia Liu,Junfeng Liu,Weihua He,Youpeng Qu,Nanqi Ren,Yujie Feng

DOI: https://doi.org/10.1016/j.jpowsour.2014.04.005

IF: 9.2

2014-01-01

Journal of Power Sources

Abstract:Different types of treatment methods for anode materials are reported to enhance power production in microbial fuel cells (MFCs). Here we report a simple, cost-effective and environmentally friendly electrochemical oxidation technique that is used to modify the carbon cloth for the improvement of MFC performance. Carbon cloth is immersed in a 5% NH4HCO3 solution and then the solution is oxidized at different set currents. Optimal performance is obtained at 14 mA cm(-2) with an oxidation time of 2 min, based on production of a maximum power density of 939 +/- 7mW m(-2) in MFC tests, which is 14.2% higher than that of the untreated carbon cloth control. This treatment method increases the electrochemical active surface area by 2.9 times (from 11.2 to 44.1 cm(2)), and improves the exchange current density by 41% (from 4.79 x 10(-4) to 6.76 x 10(-4) A m(-2)). XPS analysis indicates that electrochemical oxidation in this solution introduced amide groups onto the electrode surface, which likely improves bacterial adsorption and current production. These results show that simple electrochemical treatment method can increase active surface area and alter carbon cloth anodes in ways that increase power production of the MFC. (C) 2014 Elsevier B.V. All rights reserved.
Improving power output in microbial fuel cells with free-standing CoC x /Co@CC composite anodes

Guilian Li,Minqiao Lu,Fan Wang,Yueteng Hou

DOI: https://doi.org/10.1016/j.electacta.2023.143290

IF: 6.6

2023-10-05

Electrochimica Acta

Abstract:Microbial fuel cells (MFCs) are being recognized as a promising solution for sustainable energy generation and wastewater treatment . Despite their potential, MFCs face certain challenges that must be overcome, such as the problem of low power output caused by inefficient extracellular electron transfer (EET). In this study, we develop a nanoporous CoC x /Co@CC composite anode using microwave-assisted and high-temperature calcination methods to enhance EET efficiency and bacterial adhesion in MFCs. Compared with pure carbon cloth (CC) anodes, MFCs with CoC x /Co@CC anodes exhibit a 1.24-fold increase in power density, with a maximum output of 2693 mW m −2 . The improved performance can be attributed to the lower charge transfer resistance (R ct ) and higher redox activity of the CoC x /Co@CC anode. Cobalt's multiple valence states enhance its ability to transfer electrons between microorganisms and electrodes, ultimately increasing the overall redox activity. The CoC x /Co@CC anode also promotes the growth and enrichment of exoelectrogens, with Geobacter being enriched up to 75 % at the anode, compared with 46 % at the CC electrode. These findings demonstrate the potential of CoC x /Co@CC anodes for improving the EET efficiency of MFCs, which can have significant implications for sustainable energy and wastewater treatment.

electrochemistry
3D Porous Sponge/Carbon Nanotube/Polyaniline/Chitosan Capacitive Bioanode Material for Improving the Power Generation and Energy Storage Performance of Microbial Fuel Cells

Yuyang Wang

DOI: https://doi.org/10.3390/coatings14020152

IF: 3.236

2024-01-23

Coatings

Abstract:Anode materials play a crucial role in the performance of microbial fuel cells (MFCs) in terms of power output. In this study, carbon nanotube (CNT)/polyaniline (PANI)/chitosan (CS) composites were prepared on a porous sponge matrix. The high electrical conductivity of CNTs, the capacitive behavior of PANI, and the biocompatibility of CS were leveraged to enhance the electricity generation and energy storage capabilities of MFCs. Experimental results demonstrated that the MFC with the modified anode achieved a maximum power density of 7902.4 mW/m3. Moreover, in the charging–discharging test, the stored electricity of the S/CNT/PANI/CS anode was 16.38 times that of the S/CNT anode when both the charging and discharging times were 30 min. High-throughput sequencing revealed that the modified composite anode exhibited remarkable biocompatibility and selective enrichment of electrogenic bacteria. Overall, this study presents a novel approach for developing composite MFC anode materials with energy storage functionality.

materials science, multidisciplinary,physics, applied, coatings & films
Carbon Material Optimized Biocathode for Improving Microbial Fuel Cell Performance

Hairti Tursun,Rui Liu,Jing Li,Rashid Abro,Xiaohui Wang,Yanmei Gao,Yuan Li

DOI: https://doi.org/10.3389/fmicb.2016.00006

IF: 5.2

2016-01-01

Frontiers in Microbiology

Abstract:To improve the performance of microbial fuel cells (MFCs), the biocathode electrode material of double-chamber was optimized. Alongside the basic carbon fiber brush, three carbon materials namely graphite granules, activated carbon granules (ACG) and activated carbon powder, were added to the cathode-chambers to improve power generation. The result shows that the addition of carbon materials increased the amount of available electroactive microbes on the electrode surface and thus promote oxygen reduction rate, which improved the generation performance of the MFCs. The Output current (external resistance = 1000 Ω) greatly increased after addition of the three carbon materials and maximum power densities in current stable phase increased by 47.4, 166.1, and 33.5%, respectively. Additionally, coulombic efficiencies of the MFC increased by 16.3, 64.3, and 20.1%, respectively. These results show that MFC when optimized with ACG show better power generation, higher chemical oxygen demands removal rate and coulombic efficiency.
Improving Microbial Fuel Cell Performance Using Porous Capacitive Composite Bioanode Materials with Energy Storage Function

Yuyang Wang,Guangxu Hu,Jing Dong,Jing Wang

DOI: https://doi.org/10.3390/coatings13081322

IF: 3.236

2023-07-28

Coatings

Abstract:Microbial fuel cells (MFCs) have shown promise in solving energy and environmental problems, but their practical application is limited by their low power output. In this study, carbon nanotubes/polypyrrole composite anode materials were prepared on a porous sponge matrix. By combining the porous characteristics of sponge, the good conductive properties of carbon nanotubes, and the energy storage ability of polypyrrole capacitive materials, the prepared anode exhibited a large specific capacity, high porosity, large specific surface area, good electron transport ability, and good biocompatibility. The results showed that the maximum power density of the modified anode MFC reached 7.46 W m−3, which was 2.53 times higher than that of the control anode. The stored energy Qs released by the modified anode was 235.6 C m−2, 6.5 times higher than that of the control electrode. In addition, the transfer impedance Rct of the S/CNT/PPy electrode (5.5 Ω) was much lower than that of the control anode (16.8 Ω). The research presented in this paper demonstrates a new approach to improving the power generation ability and energy storage performance of MFCs.

materials science, multidisciplinary,physics, applied, coatings & films
Modification of the anodes using MoS2 nanoflowers for improving microbial fuel cells performance

Xiaoge Lou,Zhongliang Liu,Junxian Hou,Yu Zhou,Wenwen Chen,Xiaoye Xing,Yanxia Li,Qiang Liao,Xun Zhu

DOI: https://doi.org/10.1016/j.cattod.2019.11.029

IF: 5.3

2021-03-01

Catalysis Today

Abstract:Anode, usually with limited specific surface area, poor biocompatibility and high-cost materials, is still the key obstacle for conventional dual-chamber microbial fuel cell (MFC)'s wide application. To combat this challenge, graphene-like molybdenum disulfide (GL-MoS2) nanoflowers with a lateral size 200-300 nm are successfully synthesized via a simple one-step hydrothermal method and are used to modify MFC anodes. The experimental results show that GL-MoS2 nanoflowers modified carbon cloth (CC) and stainless-steel fiber felt (SSFF) anode obtains their maximum power density of 960.4 mW·m-2 and 713.6 mW·m-2 which are 1.7 and 3.6 times of their unmodified counterparts, respectively, which indicates that the modification not only can offer large specific surface area and good biocompatibility for biofilm growth, but also makes the anode surface more accessible for microbes' colonization and substrate transfer and thus reduces polarization loss considerably. The graphene-like materials, especially those like GL-MoS2, are promising materials for excellent and cost-effective anode modification.

chemistry, physical,engineering, chemical, applied
Biomass-Derived Carbon Anode for High-Performance Microbial Fuel Cells

Jamile Mohammadi Moradian,Songmei Wang,Amjad Ali,Junying Liu,Jianli Mi,Hongcheng Wang

DOI: https://doi.org/10.3390/catal12080894

IF: 3.9

2022-01-01

Catalysts

Abstract:Although microbial fuel cells (MFCs) have been developed over the past decade, they still have a low power production bottleneck for practical engineering due to the ineffective interfacial bioelectrochemical reaction between exoelectrogens and anode surfaces using traditional carbonaceous materials. Constructing anodes from biomass is an effective strategy to tackle the current challenges and improve the efficiency of MFCs. The advantage features of these materials come from the well-decorated aspect with an enriched functional group, the turbostratic nature, and porous structure, which is important to promote the electrocatalytic behavior of anodes in MFCs. In this review article, the three designs of biomass-derived carbon anodes based on their final products (i.e., biomass-derived nanocomposite carbons for anode surface modification, biomass-derived free-standing three-dimensional carbon anodes, and biomass-derived carbons for hybrid structured anodes) are highlighted. Next, the most frequently obtained carbon anode morphologies, characterizations, and the carbonization processes of biomass-derived MFC anodes were systematically reviewed. To conclude, the drawbacks and prospects for biomass-derived carbon anodes are suggested.
Porous α-Fe2O3 nanofiber combined with carbon nanotube as anode to enhance the bioelectricity generation for microbial fuel cell

Yuanfeng Liu,Xiuling Zhang,Huiyu Li,Lichong Peng,Yue Qin,Xiaoqiu Lin,Linshan Zheng,Congju Li

DOI: https://doi.org/10.1016/j.electacta.2021.138984

IF: 6.6

2021-01-01

Electrochimica Acta

Abstract:Microbial fuel cell (MFC) is a potential technology for bioelectricity generation from waste. Unfortunately, it is still a challenge for practical application due to the low power density. Immense efforts have been extended to boost the design of bioanode, mainly including the improvement on bacterial adhesion and extracellular electron transfer (EET) between bacteria and anode. Herein, electrospun porous α-Fe2O3 nanofibers integrated with carbon nanotubes (CNTs) are developed for MFC. Benefiting from the good electricity, ultrahigh porosity and three-dimensional interpenetrated network of fabricated CNTs/α-Fe2O3, the decorated anode is capable of enriching active bacteria and promoting effective EET rate. Consequently, the MFC based on CNTs/α-Fe2O3 nanofibers as anode achieves the eminent power density of 1959 mW/m2 and high COD removal efficiency of 85.04%, superior to that of α-Fe2O3 anode (940 mW/m2; 81.66%) and bulk carbon cloth anode (432 mW/m2; 65.83%). More importantly, the CNTs/α-Fe2O3 modified anode is favorable for electrogenic active bacteria attachment, thus improving the bioelectricity performance. The consequence suggests that this strategy can offer a potential application in power production and pollutant removal.
Carbon Nanotube/Chitosan Nanocomposite As A Biocompatible Biocathode Material to Enhance the Electricity Generation of A Microbial Fuel Cell

Xian-Wei Liu,Xue-Fei Sun,Yu-Xi Huang,Guo-Ping Sheng,Shu-Guang Wang,Han-Qing Yu

DOI: https://doi.org/10.1039/c0ee00447b

IF: 32.5

2011-01-01

Energy & Environmental Science

Abstract:New developments in biocathode microbial fuel cells (MFCs) provide an increasing possibility to use the MFC technology for sustainable wastewater treatment. Enhanced oxygen reduction and biofilm formation using novel cathode materials are crucial for the biocathode MFCs. Here we report the use of a conductive and compatible carbon nanotube/chitosan nanocomposite as a new type of MFC biocathode material, which is fabricated by electrodepositing carbon nanotubes and chitosan onto a carbon paper electrode. The MFC tests reveal that the electricity generation capacity of this nanocomposite anode is superior to the control. The electricity generation and the maximum power density of the MFC with this nanocomposite increase by 67% and 130%, respectively, compared with the MFC with carbon paper biocathode. This result demonstrates that the use of such a nanocomposite offers an effective means to enhance the electricity generation of biocathode MFCs. This approach is applicable for the development of other types of materials for MFC cathodes through facilitating the electron transfer at the electrode/bacteria interface.
Combined Carbon Mesh and Small Graphite Fiber Brush Anodes to Enhance and Stabilize Power Generation in Microbial Fuel Cells Treating Domestic Wastewater

Shijia Wu,Weihua He,Wulin Yang,Yaoli Ye,Xia Huang,Bruce E. Logan

DOI: https://doi.org/10.1016/j.jpowsour.2017.01.041

IF: 9.2

2017-01-01

Journal of Power Sources

Abstract:Microbial fuel cells (MFCs) need to have a compact architecture, but power generation using low strength domestic wastewater is unstable for closely-spaced electrode designs using- thin anodes (flat mesh or small diameter graphite fiber brushes) due to oxygen crossover from the cathode. A composite anode configuration was developed to improve performance, by joining the mesh and brushes together, with the mesh used to block oxygen crossover to the brushes, and the brushes used to stabilize mesh potentials. In small, fed-batch MFCs (28 mL), the composite anode produced 20% higher power densities than MFCs using only brushes, and 150% power densities compared to carbon mesh anodes. In continuous flow tests at short hydraulic retention times (HRTs, 2 or 4 h) using larger MFCs (100 mL), composite anodes had stable performance, while brush anode MFCs exhibited power overshoot in polarization tests. Both configurations exhibited power overshoot at a longer HRT of 8 h due to lower effluent CODs. The use of composite anodes reduced biomass growth on the cathode (1.9 +/- 0.2 mg) compared to only brushes (3.1 +/- 0.3 mg), and increased coulombic efficiencies, demonstrating that they successfully reduced oxygen contamination of the anode and the bio-fouling of cathode. (C) 2017 Elsevier B.V. All rights reserved.
Carbon nanotube powders as electrode modifier to enhance the activity of anodic biofilm in microbial fuel cells.

Peng Liang,Huiyong Wang,Xue Xia,Xia Huang,Yinghui Mo,Xiaoxin Cao,Mingzhi Fan

DOI: https://doi.org/10.1016/j.bios.2010.12.002

IF: 12.545

2011-01-01

Biosensors and Bioelectronics

Abstract:Carbon nanotube (CNT) is a promising electrode material and has been used as an anode modifier in microbial fuel cells (MFCs). In this study, a new method of simultaneously adding CNT powders and Geobacter sulfurreducens into the anode chamber of a MFC was used, aiming to form a composite biofilm on the anode. The performance of MFCs such as startup time and steady-state power generation was investigated under conditions of different CNT powders dosages. Results showed that both the startup time and the anodic resistance were reduced. The optimal dosage of CNT powders pre-treated by acid was 4mg/mL for the anode chamber with an effective volume of 25mL. The anodic resistance and output voltage of the MFC with CNT powders addition were maintained around 180Ω and 650mV during 40 days operation, while those of the MFC without CNT powders addition increased from 250Ω to 540Ω and decreased from 630mV to 540mV, respectively, demonstrating that adding CNT powders helped stabilize the anodic resistance, thus the internal resistance and power generation during long-term operation. Based on cyclic voltammogram, the electrochemical activity of anodic biofilm was enhanced by adding CNT powders, though no significant increase of the biomass in anodic biofilm was detected by phospholipids analysis. There was no remarkable change of ohmic resistance with an addition of CNT powders revealed by current interrupt method, which indicated that the rate of mass transfer might be promoted by the presence of CNT powders.
Application of Surface-modified Carbon Nanotubes Powder in Microbial Fuel Cell

WANG Hui-yong,LIANG Peng,HUANG Xia

2011-01-01

Abstract:Microbial fuel cell(MFC) is a new type of wastewater treatment technology which combines electricity generation and wastewater treatment together.However,the low electricity generation performance limits the wide use of MFC.In order to further enhance the performance,surface-modified carbon nanotubes(CNTs) powder is directly added into the anode chamber to accelerate the formation of electricity generation biofilm and improve the electricity generation capacity of the whole biofilm.After adding the ammonia-treated CNTs powder,the output voltage rises quickly to 400 mV when the MFC operates only for 4 hours.After adding the mixed acid-treated CNTs powder,the maximum power density of(236±5) mW/m2 is obtained,being 40% more than that of MFC without CNTs powder.The introduction of the amino group is the main cause that shortens the start-up time,and the anode resistance reduction is the main cause that increases the power density.
Application of advanced anodes in microbial fuel cells for power generation: A review

Teng Cai,Lijun Meng,Gang Chen,Yu Xi,Nan Jiang,Jialing Song,Shengyang Zheng,Yanbiao Liu,Guangyin Zhen,Manhong Huang

DOI: https://doi.org/10.1016/j.chemosphere.2020.125985

IF: 8.8

Chemosphere

Abstract:Microbial fuel cells (MFCs) the most extensively described bioelectrochemical systems (BES), have been made remarkable progress in the past few decades. Although the energy and environment benefits of MFCs have been recognized in bioconversion process, there are still several challenges for practical applications on large-scale, particularly for relatively low power output by high ohmic resistance and long period of start-up time. Anodes serving as an attachment carrier of microorganisms plays a vital role on bioelectricity production and extracellular electron transfer (EET) between the electroactive bacteria (EAB) and solid electrode surface in MFCs. Therefore, there has been a surge of interest in developing advanced anodes to enhance electrode electrical properties of MFCs. In this review, different properties of advanced materials for decorating anode have been comprehensively elucidated regarding to the principle of well-designed electrode, power output and electrochemical properties. In particular, the mechanism of these materials to enhance bioelectricity generation and the synergistic action between the EAB and solid electrode were clarified in detail. Furthermore, development of next generation anode materials and the potential modification methods were also prospected.
Porous -Fe2O3 nanofiber combined with carbon nanotube as anode to enhance the bioelectricity generation for microbial fuel cell

Yuanfeng Liu,Xiuling Zhang,Huiyu Li,Lichong Peng,Yue Qin,Xiaoqiu Lin,Linshan Zheng,Congju Li

DOI: https://doi.org/10.1016/j.electacta.2021.138984

IF: 6.6

2021-01-01

Electrochimica Acta

Abstract:Microbial fuel cell (MFC) is a potential technology for bioelectricity generation from waste. Unfortunately, it is still a challenge for practical application due to the low power density. Immense efforts have been extended to boost the design of bioanode, mainly including the improvement on bacterial adhesion and extracellular electron transfer (EET) between bacteria and anode. Herein, electrospun porous alpha-Fe2O3 nanofibers integrated with carbon nanotubes (CNTs) are developed for MFC. Benefiting from the good electricity, ultrahigh porosity and three-dimensional interpenetrated network of fabricated CNTs/alpha-Fe2O3, the decorated anode is capable of enriching active bacteria and promoting effective EET rate. Consequently, the MFC based on CNTs/alpha-Fe2O3 nanofibers as anode achieves the eminent power density of 1959 mW/m(2) and high COD removal efficiency of 85.04%, superior to that of alpha-Fe2O3 anode (940 mW/m(2); 81.66%) and bulk carbon cloth anode (432 mW/m(2); 65.83%). More importantly, the CNTs/alpha-Fe2O3 modified anode is favorable for electrogenic active bacteria attachment, thus improving the bioelectricity performance. The consequence suggests that this strategy can offer a potential application in power production and pollutant removal. (C) 2021 Elsevier Ltd. All rights reserved.

Improving the Power Generation of Microbial Fuel Cells by Modifying the Anode with Single-Wall Carbon Nanohorns.

High‐Performance Carbon Anode Derived from Sugarcane for Packed Microbial Fuel Cells

Nano-Fe3O4 Coated on Carbon Monolith for Anode Enhancement in Microbial Fuel Cells

Functional Nanomaterial-Modified Anodes in Microbial Fuel Cells: Advances and Perspectives

High-Power Microbial Fuel Cells Based on a Carbon-Carbon Composite Air Cathode.

Anode Modification with Formic Acid: A Simple and Effective Method to Improve the Power Generation of Microbial Fuel Cells

Increasing Power Generation of Microbial Fuel Cells with a Nano-Ceo2modified Anode

Enhanced Electricity Generation for Microbial Fuel Cell by Using Electrochemical Oxidation to Modify Carbon Cloth Anode

Improving power output in microbial fuel cells with free-standing CoC x /Co@CC composite anodes

3D Porous Sponge/Carbon Nanotube/Polyaniline/Chitosan Capacitive Bioanode Material for Improving the Power Generation and Energy Storage Performance of Microbial Fuel Cells

Carbon Material Optimized Biocathode for Improving Microbial Fuel Cell Performance

Improving Microbial Fuel Cell Performance Using Porous Capacitive Composite Bioanode Materials with Energy Storage Function

Modification of the anodes using MoS2 nanoflowers for improving microbial fuel cells performance

Biomass-Derived Carbon Anode for High-Performance Microbial Fuel Cells

Porous α-Fe2O3 nanofiber combined with carbon nanotube as anode to enhance the bioelectricity generation for microbial fuel cell

Carbon Nanotube/Chitosan Nanocomposite As A Biocompatible Biocathode Material to Enhance the Electricity Generation of A Microbial Fuel Cell

Combined Carbon Mesh and Small Graphite Fiber Brush Anodes to Enhance and Stabilize Power Generation in Microbial Fuel Cells Treating Domestic Wastewater

Carbon nanotube powders as electrode modifier to enhance the activity of anodic biofilm in microbial fuel cells.

Application of Surface-modified Carbon Nanotubes Powder in Microbial Fuel Cell

Application of advanced anodes in microbial fuel cells for power generation: A review

Porous -Fe<sub>2</sub>O<sub>3</sub> nanofiber combined with carbon nanotube as anode to enhance the bioelectricity generation for microbial fuel cell