Abstract:Additive manufacturing (AM) technology for metallic alloys such as laser powder bed fusion (LPBF) brings tremendous opportunities for development of novel alloys specifically designed for AM that would desensitize the inherent process variability and requires a refined understanding of processing–structure–property relationship that would contribute to future alloy development. In this study, two different alloys, Al-6Zn-2Mg and Al-6Zn-2Mg-0.7Sc-0.3Zr in wt. pct, representing traditional and AM-specific novel aluminum alloys, respectively, were manufactured by LPBF technique using pre-alloyed gas atomized powders. The Al-Zn-Mg ternary alloys exhibited cracks at various LPBF processing parameters, primarily along the grain boundaries of the large columnar grains that extended across multiple melt pools. The severity of cracking in LPBF Al-Zn-Mg alloys was process-dependent and could be correlated to the change in alloy composition due to evaporation of Zn and Mg with high vapor pressure. The Scheil–Gulliver non-equilibrium solidification calculations showed that the Al-Zn-Mg alloys with lower Zn and Mg concentrations had smaller solidification range (i.e., ΔT) and steepness values (i.e., dT/dfs1/2$$ \left| {{\text{d}}T / {\text{d}}f_{\text{s}}^{1/2} } \right| $$ near fs1/2=1$$ f_{\text{s}}^{1/2} = 1 $$), which corresponded to a lower cracking severity. On the other hand, no cracks were observed in Al-Zn-Mg-Sc-Zr alloys, although their solidification range and steepness values were similar to the ternary Al-Zn-Mg alloys. The microstructure of Al-Zn-Mg-Sc-Zr alloys exhibited a much refined heterogeneous microstructure containing small equiaxed and columnar grains within each melt pool, owing to the heterogeneous nucleation upon primary Al3(Sc,Zr) particles. Process-dependent microstructure was observed as a result of variation in thermal gradient and cooling rate associated with LPBF parameters. Findings from this study provide guidance for the future design of AM-specific aluminum alloys and insights into the microstructural control by LPBF.

Modeling and measurements of creep deformation in laser-melted Al-Ti-Zr alloys with bimodal grain size

Microstructural Evolution of a High-Strength Zr-Ti-Modified 2139 Aluminum Alloy for Laser Powder Bed Fusion

Effects of Alloying Elements on Creep of TiAl Alloys with a Fine Lamellar Structure

Anisotropic tensile creep behavior in laser powder bed fusion manufactured Al–Mn–Mg–Sc–Zr alloy

Temperature gradient induced tough-brittle transition behavior of a high-strength Al-4.2Mg-0.4Sc-0.2Zr alloy fabricated by laser powder bed fusion additive manufacturing

Tensile Creep Behavior and Microstructure Evolution of Mg-11Gd-2Y-0.5Zr Alloy

Alloying Effect on the Room Temperature Creep Characteristics of a Ti-Zr-Be Bulk Metallic Glass

Influence of Nb, Ta and Zr on the Interdiffusion Coefficients and Solid Solution Strengthening of γ-TiAl Single Phase Alloys

Study on the Effect of Micromorphology and Creep Properties of In Situ (ZrB2 + Al2O3)/AA6016 Composites in Extruded State

The Effect of Grain Size on the Tensile and Creep Properties of Mg–2.6Nd–0.35Zn–xZr Alloys at 250 °C

Solute-induced strengthening during creep of an aged-hardened Al-Mn-Zr alloy

Microstructural evolution of Mg–14Gd–0.4Zr alloy during compressive creep

Abnormal creep behavior of Mg-12Gd-1MM-0.6Zr (wt.%) alloy at 300C

Inhibiting Creep in Fine-Grained MgAl Alloys Through Grain Boundary Stabilization

High-temperature Creep Mechanism of Ti-Ta-Nb-Mo-Zr Refractory High-Entropy Alloys Prepared by Laser Powder Bed Fusion Technology

Creep Deformation Mechanism and Microstructure Evolution of Mg-3Sm-0.5Zn-0.4Zr Alloy

An additively manufactured near-eutectic Al-Ce-Ni-Mn-Zr alloy with high creep resistance

Process-Dependent Composition, Microstructure, and Printability of Al-Zn-Mg and Al-Zn-Mg-Sc-Zr Alloys Manufactured by Laser Powder Bed Fusion

A microstructure with improved thermal stability and creep resistance in a novel near-alpha titanium alloy

Cavitation-resistant intergranular precipitates enhance creep performance of θ'-strengthened Al-Cu based alloys

Dynamic Recrystallization-Dependent High-Temperature Tensile Properties and Deformation Mechanisms in Al-Mg-Sc-Zr Alloys