Abstract:To bring the potential power of the capacitively coupled contactless conductivity detection ((CD)-D-4) technique to full play and extend the application fields of (CD)-D-4, our previous work has developed a (CD)-D-4 sensor which is suitable for conductivity detection of electrolyte solution in industrial fields (Sensors and Actuators A 213 (2014) 1-8). With the introduction of series resonance principle, the (CD)-D-4 sensor can overcome the influence of coupling capacitances on conductivity measurement. By a specific design of shield configuration, the (CD)-D-4 sensor can overcome the influence of stray capacitances and the environment interference in industrial fields. Although the measurement performance of the (CD)-D-4 sensor is satisfactory and it is suitable for the conductivity detection in industrial fields, the input-output characteristic of the (CD)-D-4 sensor is non-monotonic, which may limit the practical applications of the (CD)-D-4 sensor. To overcome this drawback, an improved (CD)-D-4 sensor for conductivity detection in industrial fields has been developed. The basic conductivity measurement method (the series resonance principle) and the shield configuration of the improved (CD)-D-4 sensor are the same as those of the (CD)-D-4 sensor in our previous work. However, the measurement circuit of the detection path of the improved (CD)-D-4 sensor has been optimized. The one-inductor design has been replaced by a two-inductor design. With this optimization, the input-output characteristic of the improved (CD)-D-4 sensor is theoretically monotonic. Conductivity measurement experiments were carried out on four pipes with inner diameters of 1.8 mm, 3.3 mm, 5.0 mm and 7.6 mm, respectively. The experimental results indicate that the development of the improved (CD)-D-4 sensor is successful. In comparison with the previous (CD)-D-4 sensor, the measurement accuracy of the improved (CD)-D-4 sensor is comparable. But, the improved (CD)-D-4 sensor has the advantages of the monotonic input-output characteristic and the convenience for practical conductivity detection in industrial fields. Meanwhile, it is found that the input-output characteristic of the improved (CD)-D-4 sensor is nonlinear and the sensitivity of the improved (CD)-D-4 sensor decreases with the increase of conductivity. (C) 2015 Elsevier B.V. All rights reserved.

Numerical analysis and structural optimization of a DLC coated capacitance wire-mesh sensor for measuring liquid metal-gas two-phase distribution

Design of Capacitively Coupled Contactless Conductivity Detection Sensor

Design and Implementation of an Industrial C4D Sensor for Conductivity Detection

A New Sensor for the Void Fraction Measurement of Gas-Liquid Two-Phase Flow

An Improved Capacitively Coupled Contactless Conductivity Detection Sensor for Industrial Applications

Design and optimization of a new type of contactless radial C4D sensor

A C~4D-Based Measurement System of Gas-Liquid Two-Phase Flow

Measurement of Bubble Velocity Using Capacitively Coupled Contactless Conductivity Detection (C4D) Technique

Capacitively Coupled Contactless Conductivity Detection Based On Phase-Sensitive Demodulation Principle

Void Fraction Measurement Of Gas-Liquid Two-Phase Flow Based On (Cd)-D-4 Technique

A new method for the velocity measurement of gas-liquid two-phase flow

Numerical Simulation of a Magnetic Corrosion Detector for Corrosion Detection of Steel Rebar in Concrete

Measurement of Bubble Velocity Based on C~4D Technique

Design, fabrication and validation of an electrical conductivity principle based two-phase detection sensor array for molten lead (Pb) based heavy metal coolants up to 600^∘C

Electromagnetic Field and Temperature Field Analysis of Coil Type Lead-Bismuth Electromagnetic Flowmeter

Metal Capacitive Micro-pressure Sensor Diaphragm Welding Technology

Simulation and Optimization Design of Inductive Wear Particle Sensor

Optimization of Helical Capacitance Sensor for Void Fraction Measurement of Gas-Liquid Two-Phase Flow in a Small Diameter Tube

Design Optimization and Measurement Uncertainty of an Electromagnetic Level Sensor for Liquid Metal Reactors

Design and Numerical Simulation on Local Dry Welding Rotating Arc Sensor

An Online Monitoring System for In Situ and Real-Time Analyzing of Inclusions within the Molten Metal