Abstract:Welded steel plates are widely used in various structural applications, and the presence of inclined welds is often encountered in practical scenarios. Carbon fiber reinforced polymer (CFRP) has been proven to be effective for strengthening steel structures. However, the behavior of CFRP-strengthened welded steel plates with inclined welds, particularly considering the influence of welding residual stress, is limited. This paper aims to investigate the tensile behavior of CFRP-strengthened welded Q355 steel plates with inclined welds considering welding residual stress (WRS). First, WRS data were obtained by the X-ray diffraction (XRD) method at different locations. The maximum tensile and compressive residual stresses are 0.39 and 0.14 times the yield strength of the steel, respectively. Then, finite element models were established to investigate the effects of weld angles, weld width, and height on the WRS distribution of welded steel plates. Finally, the tensile performance of CFRP-strengthened welded plates with WRS was studied by numerical simulation. The results showed that the weld angles have little effect on the distribution pattern of residual stress but significantly affect the peak tensile WRS. When the weld angle changes from 0° to 60°, the peak tensile WRS decreases significantly from 0.32 to 0.06 times the yield strength of steel; furthermore, the influence of weld width and height on WRS is relatively limited. Under tension loading, the maximum stress occurs near the weld. The ends of the weld enter the yielding state later than the middle part of the weld due to the distribution of the WRS. As the weld angle increases and the length of the weld increases, the stress in the weld zone decreases, while the stress in the base material zone correspondingly increases. In addition, CFRP strengthening can reduce the magnitude of stress. This study provides preliminary references for understanding the tensile behavior of CFRP-strengthened welded steel plates with inclined welds.

Study on Probability Model and Length Effect of Tensile Strength of Unidirectional CFRP Plate

Analysis of the Tensile Properties and Probabilistic Characteristics of Large-Tow Carbon Fiber-Reinforced Polymer Composites

Experimental Study of Mechanical Properties of CFRP under Different Strain Rates and Temperatures

Micromechanical modeling for longitudinal tensile property of unidirectional CFRP considering dispersion of fiber properties

Research on Piezoresistive Effect and Random Model of Carbon Fiber Bundle

Experimental Study on Fatigue Behavior of Tensile Steel Plates Strengthened with CFRP Plates

CFRP Strengthened RC Beams with Pre-Strengthening Non-Uniform Reinforcement Corrosion Subjected to Post-Strengthening Wetting/drying Cycles

Experimental and Numerical Study of Corrugated Anchors for CFRP Plates

STUDY ON FATIGUE BEHAVIOR OF CRACKED TENSILE STEEL PLATES REINFORCED WITH CFRP PLATES

A Dynamic Constitutive Model and Simulation of Braided CFRP under High-Speed Tensile Loading

Failure Modes and Strength Prediction of Thin Ply CFRP Angle-Ply Laminates

Failure analysis of unidirectional FRP with fiber clusters under transverse pure shear

Experimental and theoretical investigation on tensile properties and fracture behavior of carbon fiber composite laminates with varied ply thickness

Effect of resin-rich areas on failure behavior of unidirectional CFRP under transverse pure shear

Tensile strength prediction of unidirectional polyacrylonitrile (PAN)-based carbon fiber reinforced plastic composites considering stress distribution around fiber break points

Long-term Behavior of CFRP Plates under Sustained Loads

A Combined Experimental and Computational Analysis of Failure Mechanisms in Open-Hole Cross-ply Laminates under Flexural Loading

Weibull Distribution-Based Prediction Model for Compression after Impact (CAI) Strength of CFRP Laminates

Finite Element Analysis for the Fatigue Behavior of Steel Plates Strengthened with CFRP Plates

Failure analysis and experimental study on bolted composite joints based on continuum damage mechanics

Study on CFRP-Strengthened Welded Steel Plates with Inclined Welds Considering Welding Residual Stress