Abstract:OBJECTIVE:To compare the retentions of different designs of cobalt-chromium (Co-Cr), pure titanium (CP Ti), and titanium alloy (Ti-6Al-4V) removable partial denture (RPD) circumferential clasps manufactured by selective laser melting (SLM) and to analyze the stress distribution of these clasps during the removal from abutment teeth. METHODS:Clasps with clasp arm size A (1.9 mm width/1.1 mm thickness at the body and 0.8-taper) or B (1.2 times A) and 0.25 mm or 0.50 mm undercut engagement were modeled on a prepared first premolar die, named as designs A1, A2, A3, and A4, respectively. The density and elastic modulus of SLM-built Co-Cr, CP Ti, and Ti-6Al-4V were measured and given to different groups of clasps. The density, elastic modulus, and Poisson ' s ratio of enamel were given to the die. The control group was the cast Co-Cr clasp with design A1, to which the density and elastic modulus of cast Co-Cr alloy were given. The Poisson's ratio of all metals was 0.33. The initial 5 N dislodging force was applied, and the maximum displacement of the clasp along the insertion path was computed. The load was reapplied with an increment of 5 N than in the last simulation until the clasp was completely dislodged. The retentive force range of different groups of clasps was obtained. The retentive forces of the SLM-built Co-Cr, CP Ti, and Ti-6Al-4V clasps with equivalent computed retentive force range to the control group were validated through the insertion/removal experiment. The von Mises stress distributions of these three groups of SLM-built clasps under 15 N loads were analyzed. RESULTS:SLM-built Co-Cr, CP Ti, and Ti-6Al-4V clasps with designs B1 or B2, and Co-Cr clasps with design A2 had higher retentive forces than those of the control group. SLM-built CP Ti and Ti-6Al-4V clasps with design A1 had lower retentive forces than those of the control group. SLM-built Co-Cr clasp with design A1 and SLM-built CP Ti and Ti-6Al-4V clasps with design A2 had equivalent retentive forces to those of the control group. The insertion/removal experiment showed that the measured retentive forces of these three groups of SLM-built clasps were (21.57±5.41) N, (19.75±4.47) N, and (19.32±2.04) N, respectively. No statistically significant measured retentive force difference was found among these three groups of SLM-built clasps (P>0.05). The maximum von Mises stress of these three groups of SLM-built clasps exceeded their responding yield strength except for the Ti-6Al-4V one. CONCLUSION:SLM-built Co-Cr circumferential clasps had higher retention than CP Ti and Ti-6Al-4V ones with the same clasp arm size and undercut engagement. The retention of SLM-built circumferential clasps could be adjusted by changing the undercut engagement and clasp arm size. If SLM-built circumferential clasps are used in clinical practice, the Ti-6Al-4V clasp with clasp arm size A and 0.50 mm undercut engagement is recommended considering the long-term use of RPD in the patient's mouth.

In Vitro Cyclic Dislodging Test on Retentive Force of Two Types of Female Parts of SFI-Bar.

Biomechanical Evaluation of Cranial Flap Fixation Techniques: Comparative Experimental Study of Suture, Stainless Steel Wire, and Rivetlike Titanium Clamp

Experimental study of cranial flap fixation techniques on biomechanical evaluation

[Finite element analyses of retention of removable partial denture circumferential clasps manufactured by selective laser melting].

Biomechanical Evaluation of Cranial Flap Fixation Techniques

Retentive force variations in three polyamide and a polyetheretherketone denture attachments for implant-supported overdentures: An in vitro study

Retention Evaluation of Implant-Supported Mandibular Overdenture Using Two Different Attachment Systems: An in Vitro Study

In vitro experiment of retention strength attenuation of three attachments

Retention and fatigue performance of modified polyetheretherketone clasps for removable prosthesis

Titanium clasp fabricated by selective laser melting, CNC milling, and conventional casting: a comparative in vitro study

Overdenture retaining bar stress distribution: A finite-element analysis

The In Vitro comparison of the retention of an implant-supported stud attachment locator and straumann ball attachment at different angulations

Frictional property comparisons of conventional and self-ligating lingual brackets according to tooth displacement during initial leveling and alignment: an in vitro mechanical study

Evaluation of the mode of failure of abutments supporting implant-supported fixed partial dentures via different retention techniques

Effects of material and coefficient of friction on taper joint dental implants

In vitro study to analyze reverse torque values of attachment screws with multiple loosening/tightening preload cycles

[Influence of Retention-Form Design on the Retention of Resin-Bonded Fixed Partial Dentures].

Effect of shape and design of the internal connection of tissue-level and bone-level implants on detorque values and removal forces: An in vitro study

In vitro study of optimal removable partial denture clasp design made from novel high-performance polyetherketoneketone

Feasibility study and material selection for powder-bed fusion process in printing of denture clasps

Cerclage performance analysis - a biomechanical comparison of different techniques and materials