Abstract:This article describes the approach used to assess the performance of a Fourier transform infrared (FTIR) and principal component regression (PCR) chemometric method when measuring respirable quartz, kaolinite, and coal in samples from a variety of mines from different countries; relative to target assigned values determined using X-ray diffraction (XRD). For comparison, FTIR results using the partial least squares regression (PLSR) method are also available. Bulk dusts from 10 Australian mines were scanned using XRD and grouped into three sets based on the levels of quartz, kaolinite, and feldspar within their crystalline mineral composition. Prediction samples were generated from 5 of these Australian mine dusts, Durrans coal dust, 2 mine dusts from the UK, and a single South African mine dust (71 samples in total) by collecting the aerosolized respirable dust onto 25-mm diameter polyvinylchloride filters using the Safety in Mines Personal Dust Sampler (SIMPEDS) operating at 2.2 l min-1. The predicted values from the FTIR chemometric methods were compared with assigned target values determined using a direct on-aerosol filter XRD analysis method described in Method for the Determination of Hazardous Substances (MDHS) 101. Limits of detection (LOD) and uncertainty values for each analyte were calculated from a linear regression between target and predicted values. The uncertainty was determined using the calibration uncertainty equation for an unweighted regression. FTIR results from PCR and PLSR are very similar. For the PCR method, the LOD for quartz, kaolinite, and coal were 5, 25, and 71 µg, respectively. For quartz, an LOD of 5 µg corresponds to an airborne quartz concentration of 10 µg m-3, assuming a 4-h sampling time and collection flow rate of 2.2 l min-1. The FTIR measurement met the expected performance criteria outlined in ISO 20581 when sampling quartz for more than 4 h using a flow rate of 2.2 l min-1 at a concentration of 0.1 mg m-3 (100 µg m-3), the current workplace exposure limit in Great Britain. This method met the same performance criteria when measuring exposures at the Australian Workplace Exposure Standard (WES) concentration of 0.05 mg m-3, although in this case a sampling period greater than 8 h was needed.

Waveband Selection Within 400-4000 Cm(-1) of Optical Identification of Airborne Dust in Coal Mine Tunneling Face

A Novel Calibration Method for the Quantification of Respirable Particles in Mining Scenarios Using Fourier Transform Infrared Spectroscopy

Multiband infrared inversion for low-concentration methane monitoring in a confined dust-polluted atmosphere

Application of a Fourier Transform Infrared (FTIR) Principal Component Regression (PCR) Chemometric Method for the Quantification of Respirable Crystalline Silica (Quartz), Kaolinite, and Coal in Coal Mine Dusts from Australia, UK, and South Africa

Demonstration of Optical Microscopy and Image Processing to Classify Respirable Coal Mine Dust Particles

Microscale dispersion behaviors of dust particles during coal cutting at large-height mining face

Study of dust pollution control effect based on orthogonal test and CFD numerical simulations

Study on dust–gas coupling pollution law and selection of optimal purification distance of air duct during tunneling process

Communication: Molecular near-infrared transitions determined with sub-kHz accuracy.

Advancing respirable coal mine dust source apportionment: a preliminary laboratory exploration of optical microscopy as a novel monitoring tool

Study on the coupling pollution law of dust and gas and determination of the optimal purification position of air duct during tunnel excavation

Numerical simulation investigation on optimal dust-exhausting airflow volume in fully mechanized caving face of high-gas coal mine

A Novel Coal Mine Dust Measurement System and Experimental Analysis

Distribution characteristics of an airflow–dust mixture and quantitative analysis of the dust absorption effect during tunnel sub-regional coal cutting

CFD-based simulation study of dust transport law and air age in tunnel under different ventilation methods

Investigation of efficient dust control strategy for construction tunnels: Ventilation System's implications for cleaner production

Spatiotemporal Spreading Characteristics of Dust Aerosols by Coal Mining Machine Cutting and "Partition/multi-Level Composite Field" Atomization Dust Purification Technology

Dispersion and migration characteristics of multisource respirable dust in development panels during tunnelling processes

Optimization of wind-and-water coordinated dust reduction device for coal mine return airway based on CFD technology

Direct-on-Filter FTIR Spectroscopy to Estimate Calcite as A Proxy for Limestone ‘Rock Dust’ in Respirable Coal Mine Dust Samples

Diffusion characteristics of coal dust associated with different ventilation methods in underground excavation tunnel