Abstract:The concept of grain boundary engineering (GBE) has been proposed based on the fact that many studies have demonstrated that boundaries associated with low Sigma-value coincident site lattice (CSL) misorientations show higher resistance to intergranular fracture and corrosion, reduced susceptibility to impurity segregation and superior ductility. It is commonly accepted that for fcc metals of low to medium stacking fault energy metals, including Ni and many Ni-alloys, the most important CSL boundary for the GBE process is a Sigma 3 boundary, the occurrence of which is dominated by the formation of annealing twins. Moreover, it has been found that repetitive thermo-mechanical processing can be used to increase further the fraction of Sigma 3 (and Sigma 3(n) (n >1)) boundaries. However, the mechanism for this is not yet clear. Therefore, an investigation on the evolution of Sigma 3 boundaries during recrystallization is important for understanding the mechanisms of GBE for those materials. In the present paper the evolution of Sigma 3 boundaries during recrystallization in a 96% cold-rolled sample of pure nickel of 99.996% purity has been explored using orientation maps obtained using electron backscatter diffraction (EBSD). Each orientation map was taken from the same area after annealing for various times. Based on the EBSD data the Sigma 3 boundaries can be divided into two groups: "twin" type and "non-twin" type. These groups can be differentiated using a parameter of deviation angle (Delta theta) of boundary misorientation to the ideal twin misorientation (60 degrees < 111 >). During recrystallization incoherent twin boundaries are found to develop from coherent twin boundaries. It is also that most Sigma 3(n) (n >1) boundaries are formed by impringement of a nucleus with its n-order twins, and that the chance for such impingement events decreases significantly with increasing n. Most non-twin type Sigma 3 boundaries arise from impingement of Sigma 1 and twin type Sigma 3 boundaries. Non-twin type Sigma 3 boundaries may be more effective than twin type Sigma 3 boundaries to develop a beneficial grain boundary network.

Twin Boundary Characters Established During Dynamic Recrystallization in a Nickel Alloy

On the grain boundary character evolution in non equiatomic high entropy alloy during hot rolling induced dynamic recrystallization

In Situ Study of the Microstructural Evolution of Nickel-Based Superalloys with High Proportional Twin Boundaries Obtained by High-Temperature Annealing

Microstructure evolution and dynamic recrystallization mechanism during thermal deformation of GH4698 superalloy

Electron Backscattered Diffraction Analysis of the Effect of Deformation Temperature on the Microstructure Evolution in a Typical Nickel-Based Superalloy During Hot Deformation

EBSD Analysis of Evolution of Dynamic Recrystallization Grains and Δ Phase in a Nickel-Based Superalloy During Hot Compressive Deformation

Evolution of Annealing Twins in a Hot Deformed Nickel-Based Superalloy

Distribution and Evolution of Low-Energy Twin Boundary Density in Time−space Domain During Isothermal Compression for Ni80A Superalloy

Dynamic Recrystallization Behavior of a Γ′-Hardened Nickel-Based Superalloy During Hot Deformation

Dynamic recrystallization mechanisms of as‐extruded GH4151 alloy during hot deformation

Study of Pre-Precipitated Δ Phase Promoting Deformation Twinning and Recrystallization Behavior of Inconel 718 Superalloy During Hot Compression

Orientation-Dependent Characteristics for Residual Grains During Hot Deformation of Nickel-Based Alloy 925

Characteristic and Mechanism of Dynamic Recrystallization in a Newly Developed Fe-Cr-Ni-Al-Nb Superalloy During Hot Deformation

Evolution of Sigma 3 Boundaries During Recrystallization of Cold-Rolled Nickel Deformed to High Strain

Hot Deformation Characteristics and Dynamic Recrystallization Mechanisms of a Novel Nickel‐Based Superalloy

Discontinuous dynamic recrystallization and nucleation mechanisms associated with 2-, 3- and 4-grain junctions of polycrystalline nickel-based superalloys

The Dynamic Recrystallization Evolution and Kinetics of Ni–18.3Cr–6.4Co–5.9W–4Mo–2.19Al–1.16Ti Superalloy During Hot Deformation

Twinning Effects on the Hot Deformation Behavior of AZ31 Mg Alloy

Hot Deformation Behaviors and Three-Dimensional Processing Map of a Nickel-Based Superalloy with Initial Dendrite Microstructure

Investigation of Boundary Migration During Grain Growth in Fully Recrystallised High Purity Nickel

Influencing Mechanisms of Prior Cold Deformation on Mixed Grain Boundary Network in the Thermal Deformation of Ni80A Superalloy