Abstract:This study proposes a clustered dynamic adaptive chemistry (CDAC) method, which uses an iterative K-means algorithm to partition the computational cells into different groups according to their similarity in terms of the temperature and significant species compositions. Taking advantage of the clustered cells, the averaged thermo-chemical properties of the cells in the respective clusters are then used to identify the adaptive dynamic reduced chemistry through the method of direct relation graph with error propagation (DRGEP). Moreover, the integration of the chemical source term, which commonly dominates the computational effort in reactive flow simulations, is now performed using the dynamic adaptive reduced chemistry at the cluster level instead of the cell level. With this CDAC method, the on-the-fly DRGEP process as well as the chemistry integration only needs to be conducted at the cluster level, dramatically reducing the unnecessary repeated computation for similar computational cells. In addition, the adaptive dynamic reduced chemistry further accelerates the chemistry integration process due to less ordinary differential equations (ODEs) to be solved for each cluster. This newly proposed CDAC method was tested in multi-dimensional homogeneous charged compression ignition engine (HCCI), direct injection compression ignition (DICI) engine and constant volume chamber combustion (CVCC) fueled with diesel, biodiesel and kerosene through the use of their respective surrogate fuel mechanisms under different operating conditions. The performance of CDAC in terms of accuracy and efficiency were extensively analyzed and discussed using different user-defined parameters, mechanisms with different surrogate components and number of species as well as different meshes with different number of grid cells. Based on this analysis, the error tolerances in DRGEP and the error tolerances of the temperature and significant species' mass fraction are recommended as: epsilon(d) <= 0.001, epsilon(T) 20K and epsilon(Y) <= 0.01 to achieve less than 0.1% integral error. With these recommended user-defined tolerances, it can be observed that the current CDAC method is able to accurately predict the in-cylinder pressure as well as the species profile in HCCI, DICI and the flame lift-off length in CVCC when compared with the full chemistry calculations as well as the experimental results. Moreover, with the recommended user defined error tolerances and a chemical kinetic model of 112 species, this CDAC method is capable of achieving a computational time speed-up factor of more than 3 compared to the conventional DAC and of almost 5 compared to the full chemistry. Finally, the CDAC method coupled CFD was applied to simulate a diesel DICI engine under three different engine speeds with a detailed primary reference fuel (PRF) mechanism of more than 1000 species. The 3-D simulation could be finished in acceptable CPU time while being able to well capture the experimental in-cylinder pressure and heat release rate for all the three engine speeds. (C) 2018 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

In-Cylinder Heat Transfer Model for Diesel Engine Based on Improved Woschni Correlation

An In-Cylinder Transient Heat Transfer Model for Temperature Field Simulation of Diesel Engine Structure

A Study on Heat Transfer Model for the Dynamic Contact Boundary Between Piston Ring and Cylinder Liner

Simulation of In-Cylinder Radiative Heat Transfer of Diesel Engine with Monte-Carlo Method

Study of In-Cylinder Heat Transfer Boundary Conditions for Diesel Engines under Variable Altitudes Based on the CHT Model

Calculation of the Radiation Heat Transfer in Cylinder of Diesel Engine by the Monte-Carlo Method

Three-Dimensional Computational Fluid Dynamics Modeling of a 6V150 Diesel Engine

Multidimensional Computational Fluid Dynamics Combustion Process Modeling of a 6V150 Diesel Engine

Evaluation of Heat Transfer Correlations for HCCI Engine Modeling

Multi-Zone & Multi-Dimensional Radiation Heat Transfer Model of G4135 Diesel Engine (Ⅰ)

Three-Dimensional Computational Fluid Dynamics Modeling of the Combustion Process of a MAN L21/31 Marine Diesel Engine

Prediction of Heat Release and Nox Emissions for Direct-Injection Diesel Engines Using an Innovative Zero-Dimensional Multi-Phase Combustion Model

Optimizing heat transfer predictions in HCNG engines: A novel model validation and comparative study via quasi-dimensional combustion modeling and artificial neural networks

Investigation of piston bowl geometry and speed effects in a motored HSDI diesel engine using a CFD against a quasi-dimensional model

Computational Acceleration of Multi-Dimensional Reactive Flow Modelling Using Diesel/biodiesel/jet-Fuel Surrogate Mechanisms Via a Clustered Dynamic Adaptive Chemistry Method

Prediction of Pollutants Emissions and Performance of Direct Injection Diesel Engines with Quasi Dimensional Combustion Model

Internal Combustion Engine Heat Transfer and Wall Temperature Modeling: An Overview

A New Modeling Method to Evaluate Effective Forced-Convective Heat Transfer Rate of Pipe Flow with Endothermic Chemical Reactions

Evaluation of On-board Heat Loss Prediction Model and Polytropic Index Prediction Model for CI Engines Using Measurements of Combustion Chamber Wall Heat Flux

A Study on Determining Empirical Parameters of Quasi-Dimensional Combustion Model in a Diesel Engine

New Correlations Of Weighted Sum Of Grey Gases Model Applicable To Computational Fluid Dynamics For Oxy-Fuel Combustion And Implementation