Abstract:With the development of the highway industry and new materials, long-afterglow luminescent material as a new energy storage and environmental protection material has gradually been applied to night lighting. In this study, SrAl2O4:Eu2+ , Dy3+ long-afterglow materials were prepared by the solid-state reaction method. The luminescent properties were improved by changing the process parameters. The single-factor test results indicated that the luminescent properties were highest when flux content, calcination temperature, calcination time, and doping ratio of Eu and Dy were 5%, 1,300°C, 2 h and 1∶1 , respectively. Then, long-afterglow materials with high luminescence were prepared by adding a pore-forming agent. The structural characteristics and optical properties of the products were analyzed. X-ray diffraction (XRD) and scanning electron microscopy (SEM) analysis indicated that the addition of pore-forming agent did not change the crystal structure of the material but changed the surface morphology of the long-afterglow materials. The surface morphology of the products changed from flat and dense to a convex structure after adding pore-forming agent, and some connected pore structures were produced. The afterglow performance of products was continuously improved with the increase of pore-forming agent content. Finally, luminescent coatings were prepared by combining with fluorine-containing resin, and the performance was studied. The stability of luminescent coatings decreased with the increase of the filler:binder ratio, and the best ratio was 0.5∶1 . The luminous performance of coatings was best when the amount of long-afterglow phosphor was 40%. The luminescent coatings had good adhesion with the road surface, and the luminescence could last for more than 7 h in a dark environment.

Preparation and Research of Long Afterglow Luminescent Materials

Preparation of long-afterglow Sr4Al14O25-based luminescent material and its optical properties

Effect of Mixing Process on the Luminescent Properties of SrAl2O4:Eu2+, Dy3+ Long Afterglow Phosphors

New Preparation Process of Long Afterglow Phosphor Eu and Dy Co-doped SrAl2O4

Synthesis of long afterglow phosphor CaAl2Si2O8:Eu2+, Dy3+ via sol-gel technique and its optical properties

PREPARATION OF ULTRAFINE SrAl2O4-BASED LUMINESCENT MATERIAL DOPED WITH RARE EARTH IONS AND THEIR OPTICAL PROPERTIES

Studies on Preparation of Long Afterglow Luminescence Glass and Its Properties

The long rod‐shaped Sr2MgSi2O7:Eu2+,Dy3+ with ultrahigh afterglow performance

PREPARATION OF ULTRAFINE SrAl_O_4-BASED LUMINESCENT MATERIAL DOPED WITH RARE EARTH IONS AND THEIR OPTICAL PROPERTIES

Preparation of High-Luminescent Materials and Application of Luminescent Coatings in Road Engineering

Luminescence decay evaluation of long-afterglow phosphors

Influence of sintering conditions on the optical properties of long afterglow luminescence glass

Preparation of SrAl2O4:Dy,Eu phosphor by sol-gel processing and its luminescent properties

Preparation and optical properties of long afterglow europium-doped Ca(Sr) Al2Si2O8 electrospun nanofibers

Long afterglow luminescence mechanism of SrAl2O4-based phosphor by the thermoluminescence and positron annihilation method

Preparation of Sral2o4 : Dy,Eu Phosphor by Sol-Gel Processing and Its Luminescent Properties

Preparation of Different Al2O3/SrO Phosphors Doped Rear Earth Ions and Their Properties

Luminescent properties of SrMgAl10 O17∶Eu2+,Mn2+ high-efficiency phosphor prepared via the sol-gel combustion method

Study of Eu3+-doped Luminescence Glasses Prepared by a Sol-Gel Process

Eu AND Dy CO-DOPED Sr2MgSi2O7-BASED LONG AFTERGLOW PHOTOLUMINESCENT MATERIALS

The Characterization and Mechanism of Long Afterglow in Alkaline Earth Aluminates Phosphors Co-Doped by Eu2o3 and Dy2o3