Abstract:Abstract Aluminum can enhance heat release of energetic composite in theory. However, the commonly used micron aluminum powder has several short comings like incomplete reaction and low reaction rate. Meanwhile, outer oxide shell of nano Al particle is thicker than micro Al, which leads to low active aluminum content and insufficient heat release. On the basis of previous research, reported fluoropolymers modified Al particles were compared and suitable F2311was chosen. Sub-micron scale Al (median particle size around 200 nm) was regarded as optimum coated object in consideration of activity content of aluminum powder changing with particle size. The super fine Al powder was prepared by electrical explosion method, and encapsulated in situ by selected fluorine rubber F2311. The experiments on thermal stability demonstrated F2311 coating thickness should be no less than 3.6 nm. These results were further confirmed by EXPLO5 thermo dynamic calculation. Calculated results showed that reaction characters of F2311 encapsulated Al exceeded conventional nano Al regardless of combustion and explosion. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), laser particle size analyzer and X-ray photoelectron spectroscopy (XPS) were used to characterize coated products’ morphology, particle size distribution and interfacial bonding information. The results showed that the coated samples were generally spherical shape, with median particle size of 217.7 nm and coating thickness of 3.6 nm. The coating shell contained a small amount of alumina and aluminum fluoride besides fluoropolymer. The non-isothermal dynamic equations of Al/F2311 and Al/Al 2 O 3 were deduced by TG/DSC simultaneous thermal analysis. Compared with conventional nano-Al, the apparent activation energy of Al/F2311 decreased by 45 kJ/mol and the first exothermic peak temperature was about 10 °C earlier. Moreover, heat release was nearly twice as conventional nano-Al. TG-DSC-MS coupled measurements certified that active Al was enveloped by ‘fluorine atmosphere’ while F2311 decomposed in range of 200–400 °C. Alumina was replaced with aluminum fluoride inside coating layer during 400–550 °C, which broadened the diffusion path and then accelerated the permeation of oxidizing gas. In addition, the exothermic of Al-F was obviously larger than Al-O. Consequently, the oxidation reaction was activated rapidly, especially in initial exothermic period. Fluoropolymer encapsulated sub-micron sized Al was a latent highly activity energetic fuel and a potential candidate for aluminum powder.

Depositing of Amorphous Ferri-Oxide Nanoparticles on Surfaces of Submicron Aluminum Powder

Preparation of NiAl2O4/Al2O3 composite nanopowder

Α-Fe–al2o3 Nanocomposites Prepared by Sol–gel Method

Preparation of Fe_2O_3/Al Nanocomposite by Sol-gel Method

Amorphization and Thermal Stability of Aluminum-Based Nanoparticles Prepared from the Rapid Cooling of Nanodroplets: Effect of Iron Addition.

Preparation & characterization of composite with micron AI coating in nanometer Fe particles

Synthesis and Characterization of Iron Particles Hosted in Porous Alumina

Preparation and Properties of Iron Based Amorphous and Nano-crystalline Spraying Alloy Powder

Oxide Gel’s Deposition Behavior in Porous Aluminum

Preparation of monodispersed α-Fe<sub>2</sub>O<sub>3</sub> nanoparticles by a hydrothermal synthetic route

Synthesis of Ultrafine Amorphous Fe–B Alloy Nanoparticles Using Anodic Aluminum Oxide Templates

Preparation of Nearly Monodispersed Fe3O4/SiO2 Composite Particles from Aggregates of Fe3O4 Nanoparticles

Formation of Nanoporous Mixed Aluminum-Iron Oxides by Self-Organized Anodizing of FeAl3 Intermetallic Alloy

Various Nanoparticle Morphologies and Wettability Properties of Aluminum Oxide Films Controlled by Water Content During the Hydrothermal Reaction

Formation Mechanism of Nanoparticles in Fe–Cr–Al ODS Alloy Fabricated by Direct Oxidation Method

A latent highly activity energetic fuel: thermal stability and interfacial reaction kinetics of selected fluoropolymer encapsulated sub-micron sized Al particles

Facile Preparation of Hydrophobic Aluminum Oxide Film via Sol-Gel Method

Synthesis of Al/Fe3Al Core–shell Intermetallic Nanoparticles by Chemical Liquid Deposition Method

Oxidation Mechanism of Aluminum Nanopowders

Preparation and Surface Modification of Monodisperse Fe3O4 Nanoparticles

Nanoengineering of Iron Oxide and Iron Oxide/Silica Hollow Spheres by Sequential Layering Combined with A Sol-Gel Process