Abstract:The strength of prestressed steel strands has developed towards high strength, increasing from 1860 MPa to over 2200 MPa. The stress in the prestressed anchorage zone is more concentrated and complex, and the anchor plates for dispersed loads need to be optimized in design. This article proposes a design scheme for adding a middle pressure-bearing step based on the existing anchor plate and then establishes a 1/4 model of the concrete anchoring area of the anchor plate for finite element analysis. Based on the theory of the strut-and-tie model, the position of the middle pressure-bearing step is determined according to the maximum angle of the strut-and-tie model. Then, carry out force transfer tests in the anchorage zone for verification. The research results indicate that after adding a middle pressure bearing step to the anchor plate, the angle between the strut-and-tie model in the anchorage zone increases, and the bearing capacity improves. The position of the middle pressure-bearing step in the anchor plate is different, and the angle between the strut-and-tie models is different. According to the middle step position parameter, λ (the ratio of the effective width of the middle step to the distance from the middle step to the end face of the anchor plate) is 0.533 to optimize the anchor plate, and the bearing capacity of its anchorage zone is relatively high. The main tensile and main compressive stresses of the anchor plate after optimization increased by 6.2% and 5.74%, respectively, compared to the anchor plate before optimization. The main tensile stress of the spiral reinforcement under the anchor plate decreased by 0.59%, the main compressive stress decreased by 2.89%, and the von-Mises stress decreased by 2.32%. The side surface tensile stress of concrete under the anchor plate was reduced by 4.3 percent. Finally, three concrete specimens were poured for force transfer testing in the anchorage zone, verifying the safety and reliability of the optimized anchor plate in the 2200 MPa-level prestressed anchorage zone.

A design approach for the interior anchorage zone of post-tensioned concrete structure

MODIFICATION OF FIP STRUT-AND-TIE MODEL FOR DESIGN OF INTERIOR ANCHORAGE ZONES OF POST-TENSIONED CONCRETE STRUCTURES

Application of strut-and-tie model for design of interior anchorage zone in post-tensioned concrete structure

A Simple Computation Method of Prestressed Space Truss and Its Global-process Pretensioning Analysis

Experimental Evaluation of Strut-and-Tie Model of Anchorage Zone in Posttensioned Concrete Structures

Investigation and Improvement of Strut-and-tie Model for Design of End Anchorage Zone in Post-Tensioned Concrete Structure

Approach for Analyzing the Ultimate Strength of Concrete Filled Steel Tubular Arch Bridges with Stiffening Girder

Strut-And-Tie Model Research On Bridge Column-Pile-Footing

Pretension Process Analysis of Prestressed Space Grid Structures

Design Approach of Stiffeners in Extended End Plate Connections and Finite Element Analysis

Assessment of Internal Forces for Intermediate Anchorage Zone of Post-Tensioned Concrete Structure

An Innovative Approach to Reduce Bursting and Spalling Stresses at Anchorage Zone of Post-Tensioned Member Incorporating Different Types of Reinforcement Configuration

Optimized Design of Anchor Plates for 2200 MPa-Class Prestressing Anchorage Zones

Effect of anchorages on C-FRCM/concrete interfacial shear performance

Internal Force Calculation and Stability Analysis of the Slope Reinforced by Pre-Stressed Anchor Cables and Frame Beams

A Design Proposal for Concrete Cover Separation in Beams Strengthened by Various Externally Bonded Tension Reinforcements

Strut-and-tie Model Method for Design of Reinforced Concrete Structures:Part Ⅰ Model Development

Lateral Load Distribution of Articulated Hollow Slab Beam Bridge Strengthened by Transverse Prestressed Force

Study on Method of Simulating Spatial Effect of Prestressing Force in Bridge

The Finite Element Analysis of the End Anchorage under Larger Prestressing Load in Rehabilitation Engineering

Structural Analyses of Extruded CFRP Tendon-Anchor System and Applications in Thin-Walled Aluminum/cfrp Bridge