Abstract:Co0.5Ni0.5Fe2O4 nanofibers with diameter of 150-400 nm were fabricated by sol-gel method combined with electrospinning technology.The as-prepared fiber samples were characterized by means of TG-DTA,XRD,FTIR,FESEM,TEM and VSM techniques.The results show that the pure resultant products with spinel structure are basically formed after calcining the precursor fibers at 450 ℃ for 2 h.With the increase of the calcination temperature,the fiber diameters decrease and the mean size(D) of Co0.5Ni0.5Fe2O4 grains within the fibers gradually increase.As a result,the fiber surface morphology gradually transforms from a porous structure to a necklace-like structure.The saturation magnetizations(Ms) of the obtained Co0.5Ni0.5Fe2O4 nanofibers monotonously increase from 35.8 A·m2/kg at 450 ℃ to 80.2 A·m2/kg at 1 000 ℃ while the corresponding coercivities(Hc) initially increase and then decrease,and reaches the maximum value at about 550 ℃,which indicates that the single-domain critical size of Co0.5Ni0.5Fe2O4 in the form of nanofibers is around 30 nm.Hc of the nanofibers varies as D0.71 in a D range below the single-domain critical size,which is in good agreement with the result predicted on the basis of the random anisotropy model.In addition,the magnetic properties measured at low temperature(77 K) show the substantial enhancements in both coercivity and remanent magnetization and a relatively obvious reduction in saturation magnetization compared to the corresponding room-temperature values.

Electrospinning of TiO2 Nanofibers: the Influence of Li and Ca Doping and Vacuum Calcination

ELECTROSPINNING PREPARATION AND LUMINESCENE PROPERTIES OF CaTiO3: RE (Eu3+/Gd3+) NANOFIBERS

Preparation and characterization of doped TiO2 nanofibers by coaxial electrospining combined with sol-gel process

Fabrication and characterization of electrospun titania nanofibers

Preparation of TiO2 Nanofibres and Influence of Calcination Temperature on Photocatalytic Activity

LaMnO3 and La0.875Sr0.125MnO3 Nanofibers via Electrospinning

Effect of Heating Rate on Morphology and Structure of Cofe2o4 Nanofibers

Nanofibers containing TiO2 nanoparticles formed using conventional and non-conventional electrospinning

Titanium Dioxide Fibers Prepared by Sol–gel Process and Centrifugal Spinning

LaMnO_3 and La_(0.875)Sr_(0.125)MnO_3 Nanofibers via Electrospinning

A General Strategy to Synthesis Mg-Ti-O Nanofibers by Sol–gel Assisted Electrospinning

Developments of Spinel Ferrite Nanofibers Fabricated by Electrospinning

Fabrication and Characterization of NiTiO3 Nanofibers by Sol–gel Assisted Electrospinning

Convenient Fabrication of Carbon-Doped Titania Nanofibres by Electrospinning

Preparation of Batio3 Nanofibers Via Electrospinning

Synthesis and characterization of electrospun iron-doped lithium titanate/carbon nanofiber mats

Preparation and characterization of anatase titanium dioxide fibre by electrospinning

Electrospinning Fabrication, Characterization and Magnetic Properties of Co0.5Ni0.5Fe2O4 Nanofibers

Electrospinning Of Titania Nanofibers From Controlled Hydrolysis Of The Precursor Via In Situ Esterification

Electrospun TiO2 Nanofiber Electrode with Optimized Diameters for Lithium Ion Battery

Fabrication and Characterisation of Titanium Dioxide (Tio2)/PVA Nanofibre Composites using Electrospinning