Abstract:The chemical-vapor-deposition (CVD) process is sufficiently well developed to allow the large-scale production of carbon nanotubes (CNTs). Metal nanoparticles (Fe, Co, Ni, etc.) are usually immobilized on a solid support and then decompose the gaseous hydrocarbon feedstocks into fragmented carbon units at elevated temperatures of 700-1100°C. Metal carbides are formed and then these dominate the growth of filamentous carbon as a structural template. The produced CNTs cannot stay firmly with an inert support and so inevitably detach away, especially during liquidphase purification or mechanical treatment. The biggest difficulties when handling the loose powder are filtration in the slurry-phase operations and the large pressure drops in fixed-bed reactors. These problems very much limit the application of CNTs on a large scale. The fabrication of carbon filaments on a structured support (e.g., activated carbon, carbon fibers, porous frameworks, graphite) has also suffered from discontinuities in the structure. The future use of CNTs has also been restricted by the technical requirements and the necessary high energy consumption to operate the intense and complicated CVD process. To avoid any mechanical post-treatment of powder and the risk of explosion during CVD synthesis, we have explored a simple method to produce monolithic CNTs directly as millimeter-scale spheres, featuring an integral continuity in the structure from microscopic to macroscopic scales. The whole process of CNTs growth has been conducted in a flow of ultrapure N2, involving a set of elementary steps in the solid phase being less complex than the widely used CVD process. The growth of CNTs is based on a solid reaction mechanism and well-graphitized nanotubes can be obtained even at a temperature as low as 400C. Direct observation of all growth events is made by using in-situ transmission electron microscopy (TEM), X-ray diffraction (XRD), IR, Raman spectroscopy and thermogravimetric analysis. A commercial styrene-divinylbenzene copolymer resin was used as the carbon precursor. According to Scheme 1, the ion-exchanged resin spheres were calcined at 800C in a flow of N2 or vacuum, after which the average diameter decreases from 0.77 to 0.49 mm, while the bulk density increases from 0.55 to 0.91 g ml. A novel macroscopic structure can be clearly seen, especially after the removal of the Fe nanoparticles and the amorphous carbon species by refluxing the spheres in concentrated HNO3. As seen in Fig. 1a, the twisted nanotubes construct the monolith while keeping a spherical shape. The cross-section views of the hand-broken spheres show no difference in the structure between the bulk and the surface, indicating a homogeneous distribution of the nanotubes in the millimeter-scale spheres (Fig. 1b). The nitrogen adsorption/ desorption isotherm shows a hysteresis loop to identify a typical mesoporous feature. The measured BET surface area and the pore volume are 223.7 m g and 0.42 ml g, respectively. The distribution of the pores ranges between about 2 and 15 nm.

Low Temperature Synthesis of Multiwall Carbon Nanotubes from Carbonaceous Solid Prepared by Sol–gel Autocombustion

Study of Controlled Growth of Carbon Nanotubes in Microstructures at Low Temperature

Low Temperature Synthesis Of High-Density Carbon Nanotubes On Insulating Substrate

Catalyst-Free in Situ Carbon Nanotube Growth in Confined Space Via High Temperature Gradient

Synthesis of Carbon Nanotubes by Decomposing Alcohol

Growth Of High-Quality Single-Wall Carbon Nanotubes Without Amorphous Carbon Formation

Nanostructured Hybrid Carbon Nanotube/UltraHigh‐Temperature Ceramic Heterostructures: Microstructure Evolution and Forming Mechanism

Large-Scale Synthesis and Magnetic Property of Carbon Nanotubes

Homogeneous carbon nanotube/carbon composites prepared by catalyzed carbonization approach at low temperature

EXPERIMENTAL RESEARCH ON SYNTHESIS OF CARBON NANOTUBES

Large‐Scale Synthesis, Annealing, Purification, and Magnetic Properties of Crystalline Helical Carbon Nanotubes with Symmetrical Structures

Low-temperature Solution Synthesis of Carbon Nanoparticles, Onions and Nanoropes by the Assembly of Aromatic Molecules

Synthesis Of High Quality Single-Walled Carbon Nanotubes By Cvd And Effect Of Catalyst'S Acidity-Basicity On Nanotubes Growth

Synthesis,Characterization and Performance of Helical Carbon Nanotubes

Synthesis of nanostructured carbon through ionothermal carbonization of common organic solvents and solutions.

Synthesis of carbon nanotube/anatase titania composites by a combination of solgel and self-assembly at low temperature

Synthesis Of Carbon Nitride Nanotubes With The C3n4 Stoichiometry Via A Benzene-Thermal Process At Low Temperatures

Synthesis and Enhanced Field-Emission of Thin-Walled, Open-Ended, and Well-Aligned N-Doped Carbon Nanotubes

Solid-state Synthesis of "Bamboo-Like" and Straight Carbon Nanotubes by Thermolysis of Hexa-Peri-hexabenzocoronene-cobalt Complexes.

Synthesis of silicon carbide nanomaterials by microwave heating: Effect of types of carbon nanotubes

Spherical Multi-Walled Carbon-Nanotube Architectures : Formation Mechanism and Catalytic Performance