Abstract:Electromagnetic stirring (EMS) has been demonstrated to have significant effect on molten metal in terms of crystal orientation, grain refinement and macro appearance of solidified structures by making use of Lorentz force. In the present study, resistance spot welding (RSW) process of 1.25 mm thick dual-phase steel DP780 with and without the external magnetic field applied has been experimentally investigated. Impacts of the EMS method on nugget appearance, quasi-static performance, fatigue life, and fracture morphology have been systematically discussed. Results of the metallographic tests showed that, compared with the traditional resistance spot weld (RSW weld), the weld under the EMS effect (EMS-RSW weld) was wider and thinner with an obvious increase in nugget diameter. Besides, within the EMS-RSW weld, crystal orientation along the faying surface of workpieces was less directional and the grains were refined. Slightly higher uniformity in the fusion zone and more notable softening in the heat affected zone of the EMS-RSW weld were observed by microhardness tests. With regard to the mechanical properties, both tensile-shear and cross-tension samples of the EMS-RSW welds exhibited higher ultimate failure loads and longer elongations at the failure points than that of the traditional RSW welds. The EMS-RSW welds also showed longer fatigue life under dynamic tensile-shear loads, especially in high cycle conditions. Furthermore, the EMS-RSW welds exhibited a higher frequency of button-pullout fractures under the welding current close to the minimum current that the traditional RSW welds required to prevent weld interfacial fractures under quasi-static tensile-shear loads. Even if both types of the welds exhibited interfacial fractures under a relatively weak welding current, more dimples were found in the fracture surfaces of the EMS-RSW welds than that of the traditional RSW welds. It can be concluded that the external magnetic field during RSW process could improve weld performance of DP780 by enhancing weld strength and plasticity. EMS could be an effective method to improve the weldability in RSW of advanced high strength steel, ultra high strength steel, and even light metals.

Effect of Electrode Force Change on Spot Weld Quality of AHSS Using Servo Gun

Effect of Electrode Force on Spot Weld Quality of High Strength Steels with Different Thicknesses and Materials

Numerical study on the effect of electrode force in small-scale resistance spot welding

Fatigue and impact properties of single and double resistance spot welding for high-strength steel used in automotive applications

Optimisation and study of a welding process for aluminium and galvanised steel based on resistance welding

Influence od the process parameters on the quality a efficiency of the resistance spot welding process of advanced high strength complex phase stells

Effect of Weld Parameters on Weld Quality in Sheet to Tube Joining with Simulation and Experimental Research

Orthogonal Optimization of Resistance Spot Welding Parameters and Microstructure and Mechanical Property of Aluminum Alloy/High Strength Steel Joint

Comparative Study of Small Scale and 'large Scale' Resistance Spot Welding

Effect of Welding Parameters of Resistance Spot Welding on Mechanical Properties and Corrosion Resistance of 316L

Research on online intelligent welding system based on resistance spot welding of aluminum galvanized steel

Impact of External Magnetic Field on Weld Quality of Resistance Spot Welding

The Effect of Welding Current and Electrode Force on the Heat Input, Weld Diameter, and Physical and Mechanical Properties of SS316L/Ti6Al4V Dissimilar Resistance Spot Welding with Aluminum Interlayer

Investigating the Effect of Electrode Pressure on Nugget Size, Microstructure and Tensile Shear Strength of Resistance Spot Welded Advanced High Strength Dual Phase Steel Joints

Failure behavior of resistance spot welded advanced high strength steel: The role of surface condition and initial microstructure

Effects of Electrode Combinations on RSW of 5182-O/AlSi10MnMg Aluminum

Research on the Welding Process and Weld Formation in Multiple Solid-Flux Cored Wires Arc Hybrid Welding Process for Q960E Ultrahigh-Strength Steel

Effects of the Applied Magnetic Field on the Quality of Resistance Spot Welding in Rail Vehicles Using Stainless-Steel

Effect of current configuration on weld properties and microstructure in synchronised twin-wire pulsed MAG welding

Resistance spot welding of high-strength low-alloyed (HSLA) 420 steel and bake-hardening (BH) 220 steel

Effect of Laser Welding Parameters on the Microstructure and Tensile Properties of Low-Alloy High-Strength Steel