Abstract:Purpose This study aims to investigate the machining performance of CVD-coated carbide tools by considering most crucial machinability aspects: cutting force, tool life, surface roughness and chip morphology in high-speed hard turning of AISI 4340 alloy steel under a sustainable minimum quantity lubrication (MQL) environment. Design/methodology/approach The purpose of this study is to analyze the performance of coated carbide tools under MQL environment therefore, machining tests were performed in accordance with the Taguchi L9 orthogonal array, accommodating the three crucial machining parameters such as cutting speed (V = 300–400 m/min), feed rate (F = 0.1–0.2 mm/rev) and depth of cut (DOC = 0.2–0.4 mm). The measured or calculated values obtained in each experimental run were validated for normality assumptions before drawing any statistical inferences. Taguchi signal-to-noise (S/N) ratio and analysis of variance methodologies were used to examine the effect of machining variables on the performance outcomes. Findings The quantitative analysis revealed that the depth of cut exerted the most significant influence on cutting force, with a contributing rate of 60.72%. Cutting speed was identified as the primary variable affecting the tool life, exhibiting a 47.58% contribution, while feed rate had the most dominating impact on surface roughness, with an overall contributing rate of 89.95%. The lowest cutting force (184.55 N) and the longest tool life (7.10 min) were achieved with low machining parameters at V = 300 m/min, F = 0.1 mm/rev, DOC = 0.2 mm. Conversely, the lowest surface roughness (496 nm) was achieved with high cutting speed, low feed rate and moderate depth of cut at V = 400 m/min, F = 0.1 mm/rev and DOC = 0.3 mm. Moreover, the microscopic examination of the chips revealed a serrated shape formation under all machining conditions. However, the degree of serration increased with an incremental raise with cutting speed and feed rate. Research limitations/implications The study is limited to study the effect of machining parameters within the stated range of cutting speed, feed rate and depth of cut as well as other parameters. Practical implications Practitioners may consider to adopt this machining technique to create more sustainable working environment as well as eliminate the disposal cost of the used metal cutting fluid. Social implications By applying this machining technique, diseases caused by metal cutting fluid to the mechanist will be significantly reduced, therefore creating better lifestyles. Originality/value Hard turning is commonly carried out with advanced cutting tools such as ceramics, cubic boron nitride and polycrystalline cubic boron nitride to attain exceptional surface finish. However, the high cost of these tools necessitates exploration of alternative approaches. Therefore, this study investigates the potential of using cost-effective, multilayer-coated carbide tools under MQL conditions to achieve comparable surface quality. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-01-2024-0013/

Experimental Study on High-Speed Turning of Free-Cutting Steel AISI 12L14 Using Multi-Layer Coated Carbide Tools

Influence of Tool Geometrical Parameters on High Speed Cutting of Titanium Alloy Ti6Al4V

Cutting performance of coated carbide inserts in hard turning of hardened AISI D2 cold work tool steels

Turning of hardened AISI H13 steel with recently developed S3P-AlTiSiN coated carbide tool using MWCNT mixed nanofluid under minimum quantity lubrication

Experimental Study on the Performance of Coated Carbide Tools in the Ultra-Precision Machining of Stainless Steel

Performance Analysis Of Aisi 4340 Hardened Steel In Dual Jet Mql Turning System: A Comparison Study Between Cvd And Pvd-Coated Carbide Tools

Study on the Orthogonal Cutting Process of Al7050T7451 with Uncoated and Coated Tools

Investigation on the Performance of Coated Carbide Tool during Dry Turning of AISI 4340 Alloy Steel

Optimization of Surface Quality and Power Consumption in Machining Hardened AISI 4340 Steel

Experimental investigation of uncoated, single layer, and multilayer-coated TiAlN/TiN tool inserts in dry orthogonal cutting of AISI/SAE 4140 alloy steel

High-speed turning of AISI 4340 alloy steel using carbide tools in a sustainable minimum quantity lubrication environment

Analysis of Wear Mechanisms Under Cutting Parameters: Influence of Double Layer TiAlN/TiN PVD and TiCN/Al2O3 Chemical Vapor Deposition-Coated Tools on Milling of AISI D2 Steel

Comparison of Tool Wear, Surface Roughness, Cutting Forces, Tool Tip Temperature, and Chip Shape during Sustainable Turning of Bearing Steel

Machinability Comparison of TiCN-Al2O3-TiN, TiAlN-TiN, and TiAlSiN Coated Carbide Inserts in Turning Hardened AISI 4340 Steel Using Grey-Crow Search Hybrid Optimization

Experimental and 3D-Deform Finite Element Analysis on Tool Wear during Turning of Al-Si-Mg Alloy

Optimization of flank wear and surface quality in the turning of 1.2343 tool steel using carbide tools coated via different methods

Hard turning of AISI H10 steel using AlTiN and AlTiSiN coated carbide tools: comparative machining performance evaluation and economic assessment

An in-depth analysis of tool wear mechanisms and surface integrity during high-speed hard turning of AISI D2 steel via novel inserts

Alloy Coated Cutting Tool Wear Characteristics Experimental Study in Fine Boring

Enhancing Wear Resistance and Cutting Performance of a Long-Life Micro-Groove Tool in Turning AISI 201

Experimental Investigation of Surface Integrity in Finish Dry Hard Turning of Hardened Tool Steel at Different Hardness Levels