Abstract:Ti–6Cr–5Mo–5V–4Al (Ti-6554) alloy has wide applications for large load-bearing components in the aerospace field. However, during the hot forming process of the alloy in the α+β phase region, there are a variety of interaction and restriction softening mechanisms and complex texture evolution behaviors, which jointly affect the microstructure and mechanical properties. This paper systematically studies the softening mechanism and texture evolution of Ti-6554 alloy in the α+β phase region using electron backscatter diffraction (EBSD), including dynamic phase transformation (DPT) and dynamic spheroidization of α phase and dynamic recrystallization (DRX) of β phase. Firstly, the effect of deformation parameters on the DPT is studied, and it is found that the volume fraction of α phase declines gradually with raising the strain rate, deformation temperature and deformation amount. The yield stress and the driving force for DPT increase with raising the strain rate and decreasing the deformation temperature. The equiaxed α phase will gradually transform into the lamellar α phase during the spheroidization process, accompanied by the wedging of the β phase. The combined effect of DPT and dynamic spheroidization leads to α grain refinement. Furthermore, the effect of deformation parameters on the DRX process of β phase is also investigated. The DRX degree only increases gradually with increasing the strain. Increasing the deformation temperature and decreasing the strain rate do not significantly increase the DRX volume fraction. Meantime, the DRX process of the β phase is heavily dependent on the α phase. The higher proportion of the α phase is capable of promoting continuous dynamic recrystallization (CDRX) process of β phase, while the lower proportion of the α phase will promote the transformation of CDRX into dynamic recrystallization (DDRX), but can not effectively increase the DRX degree of β phase. Further, the texture evolution shows that due to the combined effect of DPT and dynamic spheroidization, the effect of deformation parameters on the texture strength of α phase is very complicated. For the β phase, and fiber textures are easily formed during the deformation process.

Graded Transitions Homogeneity for Ti-50.8%Ni Processed by ECAP

Simulation And Experimental Investigation For The Homogeneity Of Ti49.2ni50.8 Alloy Processed By Equal Channel Angular Pressing

Tensile Deformation Behaviors of CuNi Alloy Processed by Equal Channel Angular Pressing

3D FEM Simulation of Multipass ECAP Ti-50.8%Ni at Various Temperatures

Tailoring of microstructure and shape memory properties of hot-forged NiTiNb alloy by multi-pass ECAP at high temperatures

Electron Backscatter Diffraction Investigation on Microstructure Evolution of TiB2(p)/Al-Cu Composite after Single-Pass Equal Channel Angular Pressing for Formability Assessment

Microstructure Evolution and Tensile Properties of In Situ TiB2(p)/Al-Cu Composite Processed by Modified Strain-Induced Melt Activation Method with Equal Channel Angular Pressing Pre-deformation

Thermal cycling stability of ultrafine-grained TiNi shape memory alloys processed by equal channel angular pressing

Multiple-stage Transformation Behavior of Ti 49.2 Ni 50.8 Alloy with Different Initial Microstructure Processed by Equal Channel Angular Pressing

Superelasticity and Its Stability of an Ultrafine-Grained Ti49.2ni50.8 Shape Memory Alloy Processed by Equal Channel Angular Pressing

Transformation Hysteresis and Shape Memory Effect of an Ultrafine-Grained Tininb Shape Memory Alloy

Effects of Ecae Process on Microstructure and Transformation Behavior of Tini Shape Memory Alloy

Characterization of microstructural evolution and mechanical properties of Cu-Ni-Cr alloys deformed by ECAP

Effects of Heat Treatment and Ecae Process on Transformation Behaviors of Tini Shape Memory Alloy

Effect of Ti addition on microstructure and mechanical properties of Zn-22Al alloy after ECAP

Systematic analysis of the softening mechanism and texture evolution of Ti–6Cr–5Mo–5V–4Al alloy during hot compression in α+β phase region

Experimental and Numerical Investigation of the ECAP Processed Copper: Microstructural Evolution, Crystallographic Texture and Hardness Homogeneity

Deformation Temperature and Postdeformation Annealing Effects on Severely Deformed TiNi Alloy by Equal Channel Angular Extrusion

Impact of Equal Channel Angular Pressing on Mechanical Behavior and Corrosion Resistance of Hot-Rolled Ti-2Fe-0.1B Alloy

Microstructure and mechanical properties evolution of Ti-13Nb-13Zr alloy processed by ECAP-Conform and rotary swaging

High-temperature tensile deformation behavior and microstructure evolution of Ti55 titanium alloy