Abstract:Ultrafiltration hollow-fiber membranes were prepared from polyetherimide (PEI) with a wet spinning method. The effects of N,N-dimethylacetantide (DMAc) as a solvent additive in the internal coagulant and acetic acid as a non-solvent additive in the dope solution on the morphologies and performances of the membranes were investigated. The influences of PEI dope concentration on membrane morphologies and properties were also studied. Scanning electron microscopy (SEM) indicates that the addition of DMAc into the internal coagulant changes the inner fiber surface from a dense skin layer to a porous structure. However, the pure water flux of the membrane decreases with the increase of DMAc content. On the other hand, the addition of acetic acid into the casting solution promotes the spinodal demixing of the membratte-forming system and suppresses the macrovoid formation in the membrane. A nodular structure forms in the fiber skin layer. With increasing acetic acid content, the pure water flux of the membrane increases about 4-fold and the solute retention shows a slight decrease. The mechanical properties can also be improved slightly by this additive. The thermal resistance of the PEI ultrafiltration membranes prepared in this work was examined by hot water treatment at 80 degrees C. No change was observed in the permeation performance of the membranes, while the study of mechanical properties shows that the elongation-at-break of the membrane decreases slightly. PEI was sulfonated by chlorosulfonic acid (CSA) in 1,2-dichloroethane. With the increase of the molar ratio of CSA to PEI repeat unit and/or reaction time, the ion-exchange capacity (IEC) of the sulfonated polyetherimide (SPEI) increases accordingly. Water uptake test and contact angle measurements show that the hydrophillicity of the SPEI increases with the increase of the IEC. Polyetherimide/sulfonated polyetherintide (PEI/SPET) ultrafiltration hollow-fiber membranes were also prepared with a dry-wet phase inversion method and SPEI was used as a polymer additive. SEM study reveals that the addition of SPEI induces the formation of nodular structure and suppresses the formation of finger-like macrovoids. With the increase of air-gap distance, it was found that the number of micropores formed in the outer fiber surface and the pore size increased. On the other hand, the pure water flux of the membrane reaches a maximum and then decreases, while the solute retention decreases at first and then levels off at longer air-gap. Based on the filtration of bovine serum albuntin (BSA) solution, it was found that the use of SPEI in the blend membranes increased their hydrophilicity.

Preparation and Characterization of Antimicrobial PES Ultra-Filtration Membrane Modified with Capsaicin

Engineering of hemocompatible and antifouling polyethersulfone membranes by blending with heparin-mimicking microgels

Preparation and Performance of Quaternary Ammonium Salt-Containing Methacrylate Copolymer-Based Ultrafiltration Membranes

Antifouling and Antibacterial Behavior of Membranes Containing Quaternary Ammonium and Zwitterionic Polymers

Improvement of Antifouling and Antibacterial Properties of Poly(ether Sulfone) UF Membrane by Blending with a Multifunctional Comb Copolymer

Enhancing biofouling resistance in microfiltration membranes through capsaicin-derivative functionalization

Preparation and Performance of Polyethersulfone Hollow-Fiber Membrane

Dependable Performance of Thin Film Composite Nanofiltration Membrane Tailored by Capsaicin-Derived Self-Polymer

Effects of a dual functional filler, polyethersulfone-g-carboxymethyl chitosan@MWCNT, for enhanced antifouling and penetration performance of PES composite membranes

Anti-Fouling and Anti-Bacterial Polyethersulfone Membranes Quaternized from the Additive of Poly(2-Dimethylamino Ethyl Methacrylate) Grafted Sio2 Nanoparticles

Preparation of a novel positively charged nanofiltration composite membrane incorporated with silver nanoparticles for pharmaceuticals and personal care product rejection and antibacterial properties.

Enhancing the Antifouling and Antimicrobial Properties of Poly(ether sulfone) Membranes by Surface Quaternization from a Reactive Poly(ether sulfone) Based Copolymer Additive

Preparation of PES-g-PMBA Filtration Membrane by Gamma-ray Irradiation and Its Membrane Performance for the Treatment of BSA Aqueous Solution

Preparation, characterization and application of functional polyethersulfone membranes blended with poly (acrylic acid) gels

Synthesis, characterization and application of antioxidants nanoparticles incorporated polymeric membranes

Antinociceptive effects of delta-opioid agonists in Rhesus monkeys: effects on chemically induced thermal hypersensitivity.

Preparation and characteristics of antibacterial PVDF ultrafiltration membrane modified with co-blending of ciprofloxacin and sulfamethoxazole

Preparation and characterization of improved fouling-resistant PPESK ultrafiltration membranes with amphiphilic PPESK-graft-PEG copolymers as additives

Preparation And Performance Of Ultrafiltration Membranes From Polyetherimide And Its Sulfonated Derivatives

The Preparation and Characterization of Novel Charged Polyacrylonitrile/pes-C Blend Membranes Used for Ultrafiltration

Preparation, characterization and performance of polyethersulfone ultrafiltration membranes