Abstract:Highlights • A dual phase β+α Mg-Li alloy was fabricated as reducing the Li content. • The dispersed α-Mg phases mitigate the dimension and distribution of eutectic I-Phase along grain boundaries. • The dual phase Mg-Li alloy exhibits enhanced ductility (elongation (EL) = 17.8 %) due to the improved deformation compatibility. • The continuity of slip between α-Mg and β-Li on plane pairs of {123}Li-{ 112 ̄2 }Mg and {112}Li-{ 112 ̄2 }Mg assures the deformation compatibility across interfaces. • Two strengthening mechanisms, nanoscale B2 (Li, Mg) 3 Zn-type precipitates and the microscale I-phase, are characterized. Mg-Li alloys with high lithium concentrations possess a lightweight body-centered cubic (BCC) matrix structure (β-Li). Interspersed eutectics (primarily the reticulated I-phase) often form along phase boundaries (PBs) and grain boundaries (GBs) which strengthen the alloy but cause the loss of ductility due to the brittle behavior of I-phase. By modifying the Li content, we fabricated the (β+α) biphase Mg-Li alloy in which the α-Mg phase with a hexagonal close-packed structure (HCP) is embedded in β-Li matrix, significantly increasing interface density. The high-density interfaces mitigate the distribution and dimension of the I-phase along GBs and PBs. The alloy exhibits enhanced ductility (elongation (EL) = 17.8 %) compared with the alloy without the α-Mg phase (EL = 5.1 %). Structural characterizations unveil the strengthening mechanism of the nanoscale B2 (Li, Mg) 3 Zn-type precipitates in conjunction with the microscale I-phase. The (Li, Mg) 3 Zn nanophases augment the yield and ultimate tensile strength of the alloy without a discernible compromise in ductility, predominantly due to gliding dislocations cutting through the precipitates. In contrast, the microscale I-phase presents a formidable barrier to dislocation motion, facilitating dislocation pileups at interfaces and culminating in diminished ductility across the interface. In-situ stretching techniques were employed to scrutinize the microstructural evolution of alloys during tensile deformation, elucidating that the deformation compatibility of alloys correlates with the average size of the I-phase and their distribution along GBs and PBs. Corresponding to the orientation relationship (OR) between the α-Mg and β-Li phases {110}Li//{0001}Mg and < 1 ̄11 >Li //< 112 ̄0 >Mg, the slip continuity between α-Mg and β-Li on plane pairs of {123}Li-{ 112 ̄2 }Mg and {112}Li-{ 112 ̄2 }Mg assures the deformation compatibility through facilitating the deformation across interfaces. Simultaneously, during the stretching process, the dispersed I-phase instigates the emergence of sporadic microcracks, indicating gradual damage evolution. These discoveries offer novel insights into achieving exceptional strength-ductility amalgamations in Mg-Li alloys through microstructural adjustments.

Formation of the Surface Oxide Film on As-Cast Mg-7li Alloy

Study on Structure and Properties of Microarc Oxidation Coating Formed on AM60B Magnesium Alloy

Microstructure Evolution and Properties of Mg-9Gd-0.8Al Alloy with Lamellar Phase During Extrusion at Different Temperatures

Characterisation of Li in the surface film of a corrosion resistant Mg-Li(-Al-Y-Zr) alloy

Formation of Phases and Microstructures in Al-8Si Alloys with Different Mg Content

Effect of Li Content on the Surface Film Formed on the Binary Mg–Li Alloys in NaCl Solution

Investigations on Microstructure and Mechanical Properties of Cast Mg-Gd-Y-Zn-Zr-Nd Alloy

Microstructures and mechanical properties of as-extruded Mg–8Gd–2Y–1Zn–6Li alloy

Study on the microstructure and mechanical properties of Mg–Al–Li–Zn–Ti multi-component alloy

Study of Electroless-Deposited Zn on the Surface of Mg-Li Alloy

Influence of Al-Si eutectic alloy on the mechanical behaviors and microstructure feature of ultralight dual-phase Mg-8Li-x(Al-12.6 Si) alloys

The composition-dependent oxidation film formation in Mg-Li-Al alloys

Effect of Ca Content on the Mechanical Properties and Corrosion Behaviors of Extruded Mg–7Li–3Al Alloys

Microstructure and mechanical properties of as-cast ultralight and high strength Mg-10Li-3Al-3Zn-xY alloy with multi-precipitates

Fabricating a corrosion-protective Li2CO3/Mg(OH)2 composite film on LA141 magnesium‐lithium alloy by hydrothermal method

Enhancing the ductility of cast Mg-Li alloys via dispersed α-Mg phase mitigating the dimension and distribution of interspersed eutectics along grain boundaries

Structural characterisation and degradation of Mg-Li thin films for biodegradable implants

Comparison of Microstructure, Mechanical Property, and Degradation Rate of Mg–1Li–1Ca and Mg–4Li–1Ca Alloys

Effect of Li addition on microstructure and mechanical properties of Al – Mg – Si alloy

Influence of Mg Content on Microstructure Coarsening, Molten Pool Size, and Hardness of Laser Remelted Al(- x)-Mg-Sc Alloys