Abstract:This study deals with the Nb–niobium silicide-based composites developed by the hot-pressing of Nb–Si–Ti ternary powder mixtures with a fixed Ti addition (6at.%) and Si content ranging from hypereutectic (11at.%) to near-eutectic compositions (18at.%). The effects of Si content, Ti addition and strain rates on the sample microstructural characterization, flexural strength, fracture toughness, quasi-static compressive deformation and failure processes were investigated. It was revealed that the volume fraction of silicides increased with increasing Si content, and most of the Ti atoms dissolved into the niobium silicides to form (Nb,Ti)5Si3 solid solutions instead of binary titanium silicides. The experimental evidence showed that a moderate improvement in the flexural strength, fracture toughness and compressive yield stress of the composites was achieved by the addition of Ti. Higher Si additions produced a much more remarkable enhancement in the compressive yield stress and bulk hardness, whereas both the flexural strength and fracture toughness decreased with increasing Si content owing to the existence of residual porosities in the samples. The composites showed remarkable superiority to the arc-melted Nb–Si alloys and monolithic niobium silicides in fracture toughness (8.3–13.0MPam vs. 4.5MPam), where the toughening effect was attributed mainly to crack bridging and crack deflection by the remaining ductile Nb phase. Moreover, quasi-static uniaxial compression tests at strain rates between 10–5 and 10–3s−1 indicated that the deformation behavior and failure processes were significantly affected by Si content and strain rates. The strain-rate-hardening behavior for all the strain rates was observed in the composite materials and the strain-rate sensitivity decreased with increasing Si content. At a lower strain rate, the composite materials with a hypoeutectic Si composition failed with a pseudoplastic response and at an angle of ∼45° off the compressive loading direction. However, in the case of higher strain rate and Si content, the brittle failure in the samples occurred through vertical splitting and spalling of fragments.

Preparation and Tribological Properties of Nb 1-x Ti x Se 2 Micro/Nanoparticles

Preparation and Tribological Properties of Nb1-xTixSe2 Micro/Nanoparticles

Preparation, Characterization and Tribological Properties of Nbs2-Xsex

Ultrasonic-assisted top-down preparation of NbSe2 micro/nanoparticles and hybrid material as solid lubricant for sliding electrical contact

Synthesized and tribological behavior of NbSe2 fibers

Investigation of W doped NbSe2 and tribology characteristic of its correlated copper base composites

Preparation, characterization and tribological application of nickel nanopieces

Heterodoped nanoflakes: synthesis and characterization of sulfur‐doped NbSe2 nanoflakes

Synthesis and Tribological Behavior of Surface Coated Cu Nanoparticles in Liquid Paraffin

MICROSTRUCTURE, MECHANICAL PROPERTIES AND FRICTION/WEAR BEHAVIOR OF HOT-PRESSED Si₃N₄/ BN CERAMIC COMPOSITES

Microstructures, Mechanical Properties and Tribological Behaviors of NiAl-based Composite Coatings with Various Addition of Nb

A Facile Method to Enhance the Tribological Performances of MoSe2 Nanoparticles As Oil Additives

Preparation of nano-scale molybdenum disulfide by liquid phase precipitation method and its lubricating properties

Investigation of the preparation and tribological behavior of a frictional interface covered with sinusoidal microchannels containing SnAgCu and Ti3SiC2

Friction-Induced Hardening Behaviors and Tribological Properties of 60niti Alloy Lubricated by Lithium Grease Containing Nano-BN and MoS2

Investigation on Tribological and Thermo-Mechanical Properties of Ti 3 C 2 Nanosheets/Epoxy Nanocomposites

Research on Preparation and Tribological Properties of Nano-Si02 Modified with Polymer

Microstructural and mechanical characterization of Nb-based in situ composites from Nb–Si–Ti ternary system

Effect of interfacial interaction between Nano-SiO2 and NBR on tribological properties of NBR water-lubricated bearings

Effects of the physicochemical properties of different nanoparticles on lubrication performance and experimental evaluation in the NMQL milling of Ti–6Al–4V

Preparation of Fe_3O_4 Nanopieces and Its Tribological Property in Liquid Paraffin