Abstract:Solid oxide fuel cells (SOFCs) with a high energy conversion efficiency and low emissions are considered as promising substitutes for traditional thermal power devices [ 1 ,2] . However, the conventional Ni based anode suffers from agglomeration, sulfur poisoning and carbon coking with hydrocarbon fuels, which limit its application [3] . Various alternative materials have been studied as promising SOFC anodes. Meanwhile, in situ exsolution has been developed as a fabrication strategy to prepare perovskite oxides with uniformly dispersed nanometallic particles [4] . Recently, A-site ordered PrBaMn 2 O 5+d has been reported as a promising anode with high electrical conductivity and good catalytic activity for the electrochemical oxidation of both hydrogen and hydrocarbons [5] . In this work, La 0.5 Ba 0.5 Mn 1-2x Co x Fe x O 3-δ (x=0, 0.05, 0.1) has been synthesized with the Pechini method and investigated as an anode material of SOFCs with H 2 and methane as fuels. The structure of the anode converts from a mixture of cubic and hexagonal phases to a perovskite structure with core-shell nanoparticles on the surface after reduction. The in situ exsolution process of the metals on the B sites is studied with an X-ray photoelectron spectrometer, a thermogravimetric analyzer and a transmission electron microscope. The results of the electrochemical tests demonstrate that the doping of Co and Fe into B sites effectively improve the performance of the single cell with H 2 as the fuel. A single cell with a 2CF-LBM anode layer and a 300-μm La 0.8 Sr 0.2 Ga 0.8 Mg 0.2 O 3-δ electrolyte layer exhibits a maximum power density ( P max ) of 98, 210, 383, 653 and 1479 mW cm -2 with wet H 2 as the fuel at 650, 700, 750, 800 and 850 o C, respectively, and achieves a peak power density of 503 mW cm -2 at 850 o C when fueled with wet CH 4 . Moreover, the 2CF-LBM anode exhibits a high coking resistance, and no remarkable degradation of the performance is observed when the cell is operated with methane as the fuel for more than 200 hours. Keywords: Solid oxide fuel cell; Perovskite; Anode; In situ exsolution Table 1. Abbreviations of various anode materials and the maximum output power densities of the cells fed with H 2 and CH 4 at 850 o C Anode composition Abbreviation P max,H2 (mW cm -2 ) P max,CH4 (mW cm -2 ) La 0.5 Ba 0.5 MnO 3-δ LBM 962 336 La 0.5 Ba 0.5 Mn 0.9 Co 0.05 Fe 0.05 O 3-δ 1CF-LBM 1241 389 La 0.5 Ba 0.5 Mn 0.8 Co 0.1 Fe 0.1 O 3-δ 2CF-LBM 1479 503 Figure 1. (a) Bright-field TEM image, (b) HAADF imagine with the EDS linear scanning and (c) EDS elemental map of the reduced 2CF-LBM; (d) I-V and I-P curves of the single cell in 650-850 o C with H 2 as fuel. References S. Tao, J.T. Irvine, Nature materials 2003, 2 , 320-323. Z. Shao, S.M. Haile, Nature 2004, 431 , 170-173. X.M. Ge, S.H. Chan, Q.L Liu, et al., Advanced energy materials 2012, 2 , 1156-1181. D. Neagu, G. Tsekouras, D. N. Miller, et al., Nature Chemistry 2013, 5 , 916-923. S. Sengodan, S. Choi, A. Jun, et al., Nature materials 2015, 14 , 205-209. Figure 1

Syngas Production by Catalytic Partial Oxidation of Methane over (la0.7a0.3)bo3 (A = Ba, Ca, Mg, Sr, and B = Cr or Fe) Perovskite Oxides for Portable Fuel Cell Applications

Bismuth doped Sr2Fe1.5Mo0.5O6-3 double perovskite as a robust fuel electrode in ceramic oxide cells for direct CO2 electrolysis

Methane oxidation to synthesis gas using lattice oxygen in La1−xSrxFeO3 perovskite oxides instead of molecular oxygen

Evaluation of Fe Substitution in Perovskite LaMnO3 for the Production of High Purity Syngas and Hydrogen

Co-Generation of Electricity and Syngas on Proton-Conducting Solid Oxide Fuel Cell with A Perovskite Layer As A Precursor of A Highly Efficient Reforming Catalyst

Performance of the single-chamber solid oxide fuel cell with a La 0.75 Sr0.25 Cr0.5 Mn0.5 O 3-δ -based perovskite anode

Oxygen Activity Tuning via FeO 6 Octahedral Tilting in Perovskite Ferrites for Chemical Looping Dry Reforming of Methane

Reducing d-p band coupling to enhance CO2 electrocatalytic activity by Mg-doping in Sr2FeMoO6-δ double perovskite for high performance solid oxide electrolysis cells

In situ exsolved Fe nanoparticles enhance the catalytic performance of perovskite cathode materials in solid oxide electrolytic cells

Reversible Exsolution of Iron from Perovskites for Highly Selective Syngas Production Via Chemical Looping Dry Reforming of Methane

Performance of the Single-Chamber Solid Oxide Fuel Cell with a La(0.75)Sr(0.25)Cr(0.5)Mn(0.5)O(3-delta)-Based Perovskite Anode

Electricity Generation in Dry Methane by a Durable Ceramic Fuel Cell with High-Performing and Coking-Resistant Layered Perovskite Anode

A Micro-Nano Porous Oxide Hybrid for Efficient Oxygen Reduction in Reduced-Temperature Solid Oxide Fuel Cells.

Barium‐doped Sr 2 Fe 1.5 Mo 0.5 O 6‐ δ perovskite anode materials for protonic ceramic fuel cells for ethane conversion

Mechanistic insight into catalytic conversion of methane on a Sr2Fe1.5Mo0.5O6−δ perovskite anode: a combined EIS-DRT, DFT and TPSR investigation

Syngas production through CH4-assisted co-electrolysis of H2O and CO2 in La0.8Sr0.2Cr0.5Fe0.5O3-δ-Zr0.84Y0.16O2-δ electrode-supported solid oxide electrolysis cells

A novel catalytic layer material for direct dry methane solid oxide fuel cell

Co-production of syngas and H2 from chemical looping steam reforming of methane over anti-coking CeO2/La0.9Sr0.1Fe1−xNixO3 composite oxides

In Situ Exsolved Core-Shell Nanoparticles on Perovskite Parent: A Novel High-Performance Anode for Solid Oxide Fuel Cells

In Situ Exsolved CoFe Alloy Nanoparticles for Stable Anodic Methane Reforming in Solid Oxide Electrolysis Cells

Alkali metal and alkaline earth metal perovskites for oxidative coupling of methane and oxidative dehydrogenation of ethane