Abstract:To characterize the hot deformation behavior of commonly used aluminum alloy, a homogeneous Al–Mg–Si–Mn–Cr alloy was analyzed by thermal simulation test at deformation temperature range of 653–803 K and strain rate range of 0.01–10 s−1. The flow stresses were predicted by modified Johnson–Cook model, modified Zerilli–Armstrong model and strain-compensated Arrhenius model. The results show that the three models are able to predict the flow behavior of the alloy. Strain-compensated Arrhenius model has the best simulation ability in predicting flow stresses, while the modified Johnson–Cook model has lower prediction accuracy and the modified Zerilli–Armstrong model has poorer predictive ability at low strain rates. Microstructure evolution shows that subgrain boundaries form at original grain boundaries at first, moving toward to the center of the deformed grains. The dislocation density decreases, while the number and the size of subgrains increase with the decreasing Zener–Hollomon (Z) parameter. Both dynamic recovery (DRV) and dynamic recrystallization take place in hot deformation process. DRV is considered to be the primary dynamic softening mechanism throughout the entire hot deformation range. Continuous dynamic recrystallization and discontinuous dynamic recrystallization operate concurrently at low strain rates and high temperatures. The relationship of subgrain size and predicted flow stress is presented. Moreover, activation volume is introduced to reveal the thermal activation mechanism during hot deformation.

Characterization of dynamic microstructure evolution during hot deformation of Al–4.10Cu–1.42Mg–0.57Mn–0.12Zr alloy

Hot deformation analysis and microstructure evolution of Al-Mg-Mn-Sc-Zr alloy by isothermal compression

Hot Deformation Behavior and Microstructure Evolution of High-Strength Al-Zn-Mg-Cu Alloy

Constitutive equation and hot deformation behavior of homogenized Al–7.68Zn–2.12Mg–1.98Cu–0.12Zr alloy during compression at elevated temperature

Deformation Behavior and Microstructural Evolution of Al-Zn-Cu-Mg-Sc-Zr Alloy During High Temperature Compression

Characterization of Hot Deformation Behavior of Al-Zn-Mg-Mn-Zr Alloy During Compression at Elevated Temperature

Deformation Behavior and Microstructure Evolution of Al–5.06Mg–1.67Li–0.51Zn Alloy under Hot Compression

Dynamic microstructural evolution of Al-Cu-Li alloys during hot deformation

Hot Deformation Behavior of Al-Cu-Li-Mg-Zr Alloy Containing Zn and Mn

Hot Deformation Behavior Considering Strain Effects and Recrystallization Mechanism of an Al-Zn-Mg-Cu Alloy

Constitutive Equation and Hot Compression Deformation Behavior of Homogenized Al–7.5Zn–1.5Mg–0.2Cu–0.2Zr Alloy

Deformation Behavior of an Al–Cu–Mg–Mn–Zr Alloy During Hot Compression

Dynamic Recrystallization Nucleation Mechanism and Precipitation Behavior of Homogeneous Al-Zn-Mg-Cu Alloy during Hot Deformation

Hot Deformation Behavior and Microstructure Evolution of a Novel High-Zn Containing Al-Zn-Mg-Cu-Zr Alloy

Characterization of Hot Deformation Behavior and Constitutive Modeling of Al–Mg–Si–Mn–Cr Alloy

Investigation of deformation behavior and strain-induced precipitations in Al-Zn-Mg-Cu alloys across a wide temperature range

Constitutive equation and dynamic recovery mechanism of high strength cast Al-Cu-Mn alloy during hot deformation

Dynamic recrystallization mechanisms of as-forged Al–Zn–Mg-(Cu) aluminum alloy during hot comp.ression deformation

Hot Deformation Constitutive Model and Processing Maps of Homogenized Al–5Mg–3Zn–1Cu Alloy

Hot Deformation Behavior of Mg-5Li-3Al-2Zn-0.2Zr Alloy Based on Constitutive Analysis, Processing Map, and Microstructure Evolution

Flow Behavior and Microstructural Evolution of Al–Cu–Mg–Ag Alloy During Hot Compression Deformation