Abstract:Hot-pressed and hot-deformed Nd-Fe-B magnets are generally made from rapidly quenched powder after crystallization treatment. In this work, the amorphous melt-spun ribbons are also employed directly as the precursor. The amorphous and crystallized powders with the composition of Nd28.47Pr0.56FebalB0.97Co3.63Al0.13Nb0.56Zr0.44 were employed for fabricating hot-pressed and hot-deformed magnets. The influences of processing parameters on the microstructure and magnetic properties have been investigated. For the hot-pressed magnets produced from both crystallized and amorphous powders, the grain pre-orientation and magnetic properties including coercivity, remanence and maximum energy product increase with the increasing temperature, pressure and holding time in the ranges of 650-800 oC, 300-600 MPa and 30-150 min, respectively. The hard magnetic properties of the hot-pressed magnets obtained from amorphous powder are slightly higher than those from crystalline powder due to the smaller grain size of the former. The magnetic properties of hot-deformed magnets are mainly determined by the deformation temperature and not influenced by the state of the powder and hot-pressed precursors. The hot-pressed magnets and hot deformed magnets with different microstructures exhibit different magnetization mechanisms. The optimal hot-deformation temperature is found to be 750 °C for obtaining a high maximum energy product of 39 MGOe. The present results suggest that the rapidly quenched amorphous powder can be used to not only directly prepare hot-pressed magnets with higher magnetic properties, but also to reduce the process step for hot-deformed Nd-Fe-B magnets.

Microstructure and Magnetic Properties of Anisotropic Nd–Fe–B Magnets Prepared by Spark Plasma Sintering and Hot Deformation

Hot Deformed Anisotropic Nanocrystalline Ndfeb Based Magnets Prepared from Spark Plasma Sintered Melt Spun Powders

Isotropic and Anisotropic Nanocrystalline NdFeB-Based Magnets Prepared by Spark Plasma Sintering and Hot Deformation

Microstructure and Property Evolution of Isotropic and Anisotropic Ndfeb Magnets Fabricated from Nanocrystalline Ribbons by Spark Plasma Sintering and Hot Deformation

Microstructure and Magnetic Properties of NdFeB Magnet Prepared by Spark Plasma Sintering

Reduction of the mechanical anisotropy in hot-deformed Nd-Fe-B magnets by the construction of heterogeneous structure

Magnetic microstructure and magnetic properties of spark plasma sintered NdFeB magnets

Pre-orientation Sintering: an Alternative Process to Prepare High-Performance Anisotropic Nd–Fe–B HDDR Magnets

Influences of Stain Rate on the Microstructure and Properties for Hot Deformed NdFeB Magnets

Preparation of Anisotropic Nanocrystalline NdFeB Magnets from Amorphous Powders by One‐Step Hot Deformation

Diffusion of Nd-Rich Phase in the Spark Plasma Sintered and Hot Deformed Nanocrystalline Ndfeb Magnets

Microstructure and Properties of NdFeB Magnets Prepared by Spark Plasma Sintering Using Melt Spun Powder

Isotropic and Anisotropic Nanocrystalline NdFeB Bulk Magnets Prepared by Binder-Free High-Velocity Compaction and Hot Deformation

Structure and Performance of Anisotropic Nanocrystalline Nd-Fe-B Magnets Fabricated by High-Velocity Compaction Followed by Deformation

Improved magnetic properties and fracture strength of NdFeB by dehydrogenation

Orientation Dependence of Plastic Deformation of Sintered Nd-Fe-B Magnets at High Temperature

Microstructure and Magnetic Properties of MM-Fe-B Magnets Prepared by Spark Plasma Sintering

Preparation of Highly Textured Hydrogenation-Disproportionation-desorption-recombination Powders for Nd-Fe-B Sintered Magnets

Preparation of Isotropic and Anisotropic Nanocrystalline Ndfeb Magnets by High-Velocity Compaction and Hot Deformation

Anisotropy optimization of HDDR magnetic powders by precursor alloy annealing

Comparison and process study of hot-pressed and hot-deformed Nd-Fe-B magnets prepared by amorphous and nanocrystalline powders