Abstract:The MAX phase has attracted much attention due to its unique properties combined with the merits of both metal and ceramic, including the low density, high electrical conductivity and good oxidation resistance, which makes it significant for possible applications in various high temperature or other environments. There is a lot of research work on Ti2AlX (X=C, N). However little research about thermodynamic properties at high pressure is carried out. So we study the structural, mechanical and thermodynamic properties of Ti2AlC and Ti2AlN at various pressures and temperatures. The first-principles calculations based on electronic density-functional theory framework are used to investigate the properties at various pressures. The cut-off energy is 350 eV. Converged results are achieved with 10102 special K-point meshes. The self-consistent convergence of total energy is set to be 5.010-6 eV/atom. According to the calculated structural parameters at various pressures, we can find that the ratios V/V0 (V0 denotes the system volume at 0 GPa) of Ti2AlX are reduced by 20.59% and 18.93%, respectively, so the compressibility of the system is strong. As the internal pressure increases, the curves of V/V0 become gentle. Then we calculate elastic constants at pressures ranging from 0 to 50 GPa in steps of 10 GPa. It is obvious that the Ti2AlX is mechanically stable because all of the elastic constants satisfy the Born stability criteria. The bulk modulus, shear modulus and Young's modulus linearly increase with internal pressure increasing, implying that the pressure can improve the resistance to volume deformation. The ductility and brittleness can be judged according to Pugh's criterion (ratio of bulk modulus to shear modulus B/G), and the brittle nature turns into ductile nature in a pressure range of 40-50 GPa for the Ti2AlX since the value of B/G exceeds 1.75. Finally, we study the thermodynamic properties at various pressures and temperatures based on the quasi-harmonic Debye approximation theory, including the bulk modulus, heat capacity and thermal expansion coefficient. The bulk modulus decreases with temperature increasing but increases with pressure increasing. The heat capacity at constant volume Cv and the heat capacity at constant pressure Cp have the same variation tendency, while Cv obeys the Dulong-Petit limit. It is easy to see that temperature and pressure have opposite influences on heat capacity and the effect of temperature is more significant than that of pressure. The effects of temperature and pressure on linear expansion coefficient mainly occur at low temperature and the effect of pressure is not so considerable when the pressure exceeds 30 GPa. Above all, the effects of temperature and pressure on thermodynamic properties are inverse.

Isotropic Thermal Expansivity and Anisotropic Compressibility of Reb2

Elastic Anisotropy and Thermodynamic Properties of Chromium Tetraboride from First‐principles Calculations

Thermal Equation Of State Of Rhenium Diboride By High Pressure-Temperature Synchrotron X-Ray Studies

Ab Initio Calculation of Lattice Dynamics and Thermodynamic Properties of Beryllium

First-Principles Predictions Of Phase Transition And Mechanical Properties Of Tungsten Diboride Under Pressure

Elastic Constants and Anisotropy of RuB2under Pressure

Hardness And Elastic Moduli Of High Pressure Synthesized Mob2 And Wb2 Compacts

New Exploration on Phase Transition and Structure of PbS under High Pressure and Temperature

Anisotropy in Elasticity and Physical Properties of Ti2B under High Pressure

High-Pressure High-Temperature X-Ray Diffraction Of Beta-Boron To 30 Gpa

Phase transition of intermetallic TbPt at high temperature and high pressure.

Physical Properties and Electronic Structure of Cr2B under Pressure

High-Pressure Studies of Size Dependent Yield Strength in Rhenium Diboride Nanocrystals

In situ synchrotron X-ray diffraction with laser-heated diamond anvil cells study of Pt up to 95 GPa and 3150 K

High-Pressure Studies of Rubidium Azide by Raman and Infrared Spectroscopies

Structural, Mechanical, and Thermodynamic Properties of Ti2AlX (X = C, N) at High Pressure

High Pressure in Situ Differential Thermal Analysis of Na0.5Bi0.5TiO3 Phase Transitions Up to 5 GPa

Compressibility and Thermoelasticity of CrN

First-principles Calculations of Mechanical and Thermodynamic Properties of Tetragonal Be12Ti

In Situ High-Pressure X-Ray Diffraction Experiments and Ab Initio Calculations of Co2p

High Pressure Structural Study of Β-Ti3o5: X-ray Diffraction and Raman Spectroscopy