Abstract:Cold-drawn pearlitic steel wires exhibit ultrahigh strength and have important applications where high strength and wear resistance are required. The hypereutectoid compositions present a promising potential for increasing the mechanical properties, especially the strength. The austenitization process strongly influences the following pearlitic microstructure and thus the mechanical properties. Continuous heating is always used in the industrial processing. However, the austenitization of pearlite in hypereutectoid steels during continuous heating has not been investigated systematically. In this work, the dilatometer and DSC were employed to investigate the austenitization kinetics of hypereutectoid steels during continuous heating. Microstructure evolution was observed with SEM and EBSD. The dilatometer and DSC curves were analyzed with derivative method. The whole austenitization can be divided into five stages: initial microstructure, reverse eutectoid transformation, retained cementite dissolution, homogenization and homogeneous austenite. Tangent method was used for measuring the critical temperatures of different stages. Experimental determination of transformed fraction was obtained through the lever method. Calculation with Thermo-Calc and Dictra software was carried out for the austenitization and considered to be a reasonable result by comparing with the experimental data. There is a turning point for the reduction rate of cementite and formation of austenite at the finishing temperature of reverse eutectoid transformation, which is similar with the austenitization in low carbon steel and spheroidal pearlite of hypereutectoid steel. Effects of heating rates, initial microstructure and carbon content were studied by varying the relevant parameters. Higher heating rate in- creases the starting and finishing temperatures of reverse eutectoid transformation and widens the temperature range, has no effect on the finishing temperature of retained cementite dissolution, increases the finishing temperature of homogenization. Coarser initial pearlitic microstructure increases the starting and finishing temperatures, widens the temperature range for reverse eutectoid transformation, increases the finishing temperature for retained cementite dissolution and homogenization. Enhancement of carbon content has little effect on the reverse eutectoid transformation, but increases the finishing temperature for retained cementite dissolution and homogenization. The effects mentioned above on the austenitization kinetics were discussed for mechanism analysis and compared with the observations of relevant systems provided by other research.

Predicting the Austenite Fraction After Intercritical Annealing in Lean Steels as a Function of the Initial Microstructure

Austenite Formation and Cementite Dissolution During Intercritical Annealing of a Medium-Manganese Steel from a Martensitic Condition

Kinetic Transitions and Mn Partitioning During Austenite Growth from a Mixture of Partitioned Cementite and Ferrite: Role of Heating Rate

Unlocking the Mechanisms behind Austenite Formation of Cold‐Rolled Ferrite–Martensite Dual‐Phase Steels: The Role of Ferrite Recrystallization

Prediction of the Non-Isothermal Austenitization Kinetics of Fe-C-Cr Low Alloy Steels with Lamellar Pearlite Microstructure

Excess Carbon Enrichment in Austenite During Intercritical Annealing

Influence of Intercritical Annealing on Microstructure, Ductility, and Toughness of Medium Mn Steels

Effect of Austenite Grain Size on Phase Transformation Structure of Low‐Carbon Microalloyed Steel

Numerical Simulation of Reversed Austenite Evolution during Intercritical Tempering of Low-Carbon Martensitic Stainless Steel

Volume Fractions of Proeutectoid Ferrite/Pearlite and Their Dependence on Prior Austenite Grain Size in Hypoeutectoid Fe-Mn-C Alloys

In Situ Observation of Austenite–ferrite Interface Migration in a Lean Mn Steel During Cyclic Partial Phase Transformations

Austenite/Ferrite Interface Migration and Alloying Elements Partitioning: an Overview

The austenite to polygonal ferrite transformation in low-alloy steel: multi-phase-field simulation

The In Situ Observation of Phase Transformations During Intercritical Annealing of a Medium Manganese Advanced High Strength Steel by High Energy X-Ray Diffraction

Analytical Modeling of Austenite Growth and Phase Evolution During Reverse Transformation from Pearlite in High Carbon Steels

The Effect of Prior Ferrite Formation on Bainite and Martensite Transformation Kinetics in Advanced High-Strength Steels

Investigation of Austenitization During Continuous Heating Process in Hypereutectoid Steels

Modeling of the Austenitization of Ultra-high Strength Steel with Cellular Automation Method

Process Maps for Predicting Austenite Fraction (vol.%) in Medium-Mn Third-Generation Advanced High-Strength Steels

Effect of Deformed Prior Austenite Characteristics on Reverse Phase Transformation and Deformation Behavior of High-Strength Medium-Mn Steel

Crystal Plasticity Finite Element Modeling of the Influences of Ultrafine-Grained Austenite on the Mechanical Response of a Medium-Mn Steel