Abstract:Gold catalysts supported on titania (Au-TiO(2)) and alumina (Au-Al(2)O(3)) were prepared by deposition-precipitation with urea and then activated before characterisation and reaction in CO oxidation, either by calcination in air at 500 °C or reduction under H(2) at 300 °C. Gold nanoparticles with average size in the range 2-4 nm were obtained, with calcination leading to larger gold nanoparticles than reduction. For Au-TiO(2), high activity was observed in CO oxidation at room temperature, independent of the activation treatment. This high activity could not be correlated to the presence of sub-nanometer gold clusters as reported in the literature, since they could not be detected by atomic-resolution high-angle annular dark-field scanning-transmission electron microscopy (HAADF-STEM). In the case of Au-Al(2)O(3), the performance in CO oxidation was found to strongly depend on the water content in the reaction gas feed and on the activation conditions, with calcination resulting in a poorly active catalyst whereas reduction gave activity of the same order as Au-TiO(2). A comparative study of Au-TiO(2) and Au-Al(2)O(3) by electron microscopy did not reveal distinct differences in the shapes of the Au nanoparticles, which are mostly flattened through interaction with the substrate in both samples, with side profile shapes varying from rounded hemispherical to well faceted truncated cubo-octahedra. More faceting is found for the samples calcined at 500 °C than reduced at 300 °C. Various possible parameters affecting the catalytic properties of gold in CO oxidation are discussed in the context of the relevant literature.

Preparation and characterization of Au@TiO 2 core–shell hollow nanoparticles with CO oxidation performance

Preparation of SiO2@Au@TiO2 Core–shell Nanostructures and Their Photocatalytic Activities under Visible Light Irradiation

Novel Au/TiO 2 /al 2 O 3 · X H 2 O Catalysts for CO Oxidation

Highly Active and Stable Au@CuxO Core–shell Nanoparticles Supported on Alumina for Carbon Monoxide Oxidation at Low Temperature

Self-assembly of a Highly Stable and Active Co3O4/H-TiO2 Bulk Heterojunction with High-Energy Interfacial Structures for Low Temperature CO Catalytic Oxidation

Heterostructured Catalysts Prepared by Dispersing Au@Fe2O3 Core–shell Structures on Supports and Their Performance in CO Oxidation

Effect of hydrothermal reaction time and calcination temperature on properties of Au@CeO 2 core–shell catalyst for CO oxidation at low temperature

High-Temperature-Stable Au@SnO2 Core/Shell Supported Catalyst for CO Oxidation

Au@TiO2 Core-Shell Composites for the Photocatalytic Reduction of CO2

Preparation of Core–shell Structured Au@SiO2 Nanocomposite Catalyst with Au Core Size below 2 Nm Without High-Temperature Calcination Procedure

Preparation of Au/Ti-Sba-15 Catalysts and Their Catalytic Performance for Co Oxidation

A Facile Route for Spraying Preparation of Pt/TiO2 Monolithic Catalysts Toward VOCs Combustion

Stable mass-selected AuTiO x nanoparticles for CO oxidation

Carbon Monoxide Combustion on Metal Oxide Supported Au@CuxO Catalysts at Low Temperature

Stable Mass-Selected AuTiOx Nanoparticles for CO Oxidation.

Catalytic Oxidation Of Toluene With Low Loading Bimetallic Au@Pt Core-Shell Catalyst

Preparation of TiO2-supported twinned gold nanoparticles by CO treatment and their CO oxidation activity

Substantial Pretreatment Effect on CO Oxidation over Controllably Synthesized Au/FeOx Hollow Nanostructures Via Hybrid Au/β-FeOOH@SiO2

Large-scale Synthesis and Catalytic Activity of Nanoporous Cu–O System Towards CO Oxidation

High-Surface-Area Mesoporous Crystalline TiO2: Synthesis, Characterization, and Application As Support for Making Stable Au Catalysts

HRTEM and STEM-HAADF characterisation of Au-TiO2 and Au-Al2O3 catalysts for a better understanding of the parameters influencing their properties in CO oxidation